How much transmission fluid does a 2007 Chevy Express 2500 hold?
The 2007 Chevy Express 2500, with its common automatic transmission, typically holds about 12 to 13 quarts (roughly 11 to 12 liters) of transmission fluid when fully refilled, including the torque converter. The exact amount depends on the transmission model and the servicing method, so always verify against your vehicle’s VIN-specific data and maintenance manual.
Understanding the transmission setup on the 2007 Express 2500
Most 2007 Express 2500 vans use the GM 4L60-E automatic transmission. A smaller subset of heavy-duty configurations may employ the 4L80-E. While both are GM automatics, the total fluid capacity can differ slightly between these units. For precise figures, consult the owner’s manual or GM service data tied to your VIN.
Typical guidance for the common automatic
For the well-known 4L60-E configuration that comes in the majority of these vans, plan on a full refill totaling about 12 to 13 quarts (approximately 11 to 12 liters) of transmission fluid, including the torque converter. If your van uses a different transmission type, the total capacity may vary by a few quarts; verify with exact vehicle data before servicing.
How to confirm the exact capacity for your vehicle
To ensure you add the correct amount during service, use these steps to determine the precise capacity for your specific van:
Check the owner's manual or a GM service information database using your VIN to pull the exact transmission specification for your vehicle.
Identify your transmission type by inspecting under the hood or referring to the service documentation; Dexron VI is commonly recommended for GM automatics of this era.
When refilling, start with the typical full-refill figure (about 12 quarts for the common setup) and adjust after running the engine through a few gear cycles and rechecking on a level surface with the dipstick, following the manufacturer’s recommended range.
Fluid specification and maintenance tips
Use Dexron VI automatic transmission fluid for the 4L60-E (and most GM automatics of this period). Do not mix Dexron variants. If you’re unsure about your specific transmission, consult your dealer or service manual. Regular level checks help prevent transmission damage from overfill or underfill.
Summary
For the majority of 2007 Chevy Express 2500 vans equipped with the common 4L60-E automatic, expect a total transmission fluid capacity of about 12–13 quarts (11–12 liters) for a complete refill, including the torque converter. Exact capacity can vary by transmission variant and service method, so verify with VIN-specific data and follow GM’s guidelines for fluid type and fill levels. Regular maintenance and proper fluid specification help ensure reliable operation of the transmission.
How much transmission fluid does a Chevy Express 2500 take?
For Automatic Transmission: 8L90....SL150
| Capacity: | 8 speed With Cooler 8L90 Total Fill 11.4 quarts. |
|---|---|
| Capacity: | 8 speed Trans Only 8L90 Total Fill 10.9 quarts. |
| Capacity: | 7.4 quarts Initial Fill. |
What kind of transmission fluid does a 2007 Chevy Express 2500 take?
Dexron VI/Mercon LV ATF; 1 QT.
How much transmission fluid does a 2007 Chevy 2500 hold?
Automatic Transmission Fluid
Capacity: 7.4 quarts Initial Fill.
How many quarts of transmission fluid for a drain and fill?
You will need approximately 3-6 quarts of transmission fluid for a drain and fill, but the exact amount depends on your vehicle, so it's best to measure how much you drain out and replace that amount. Always check your owner's manual for the correct type and amount of fluid for your specific make and model.
Before you begin
- Check your owner's manual to find the specific type of transmission fluid your vehicle requires.
- You can also get this information from an auto parts store, such as AutoZone.
- Purchase enough fluid for the job, plus a little extra in case of spills or to have on hand for future top-offs.
During the procedure
- Drain the old fluid: Place a catch pan under the transmission's drain plug and remove the plug to let the old fluid drain out.
- Measure the drained fluid: Measure the amount of fluid you collected in the pan. This will be the amount you need to add back into the transmission.
- Refill the transmission: Pour the new, correct type of fluid into the transmission through the fill tube. Start with the amount you just measured.
- Check the level: After refilling, start the engine and let it run for a few minutes. Check the dipstick to see if the fluid level is correct. You may need to add a little more or less to reach the "full" mark.
