How to reset TPM on Chevy Colorado?

If you own a Chevy Colorado and need to reset the Trusted Platform Module (TPM) on your vehicle, there are a few steps you can follow to get the job done. The TPM is a security feature that helps protect your vehicle's data and systems, but sometimes it may need to be reset for various reasons.

Steps to Reset TPM on Chevy Colorado

1. Locate the TPM reset button: The TPM reset button is usually located under the dashboard or in the glove compartment of your Chevy Colorado. Consult your owner's manual or contact your dealer if you're unsure of the exact location.


2. Turn off the vehicle: Make sure your Chevy Colorado is turned off before attempting to reset the TPM.


3. Press and hold the TPM reset button: Press and hold the TPM reset button for approximately 10-15 seconds until the TPM light on your dashboard starts blinking.


4. Start the vehicle: Once the TPM light is blinking, start your Chevy Colorado. The TPM should now be reset, and the light should turn off.

If the TPM light remains on or the reset process doesn't work, you may need to take your Chevy Colorado to a dealership or a qualified technician for further diagnosis and assistance.

Why Reset the TPM on Chevy Colorado?

There are a few common reasons why you might need to reset the TPM on your Chevy Colorado:

• Replacing the battery: If you've replaced the battery in your Chevy Colorado, the TPM may need to be reset to ensure it's properly configured with the new battery.


• Updating the vehicle's software: After a software update or a system reset, the TPM may need to be reset to ensure it's properly integrated with the updated systems.


• Troubleshooting issues: If you're experiencing issues with your Chevy Colorado's security systems or the TPM itself, resetting the TPM may help resolve the problem.

Resetting the TPM on your Chevy Colorado is a relatively straightforward process, but it's important to follow the steps carefully to ensure the reset is successful. If you encounter any issues or have further questions, don't hesitate to consult your owner's manual or contact your local Chevy dealer for assistance.

Where is my TPMS reset button on my Chevy?

The TPMS reset button on a Chevy is often located under the steering wheel, but the procedure can also involve using the vehicle's driver information center (DIC) or a separate tool. For many models, there isn't a simple button to press; instead, you'll need to navigate the menu in the instrument cluster and follow the "relearn tire positions" prompts to reset the system, often with a special tool to activate each sensor. If you can't find it, consult your owner's manual.
 
This video shows how to reset the tire pressure monitoring system on a 2007-2013 Chevy Silverado: 1m1A Auto: Repair Tips & Secrets Only Mechanics KnowYouTube · Feb 15, 2019
Common reset procedures

• Using the driver information center (DIC): This is the most common method for newer models. 
  1. Turn the ignition to the "On" position (without starting the engine). 
  2. Use the vehicle's buttons or steering wheel controls to navigate the DIC until you find the "Tire Pressure" or "Vehicle Settings" menu. 
  3. Select "Relearn Tire Positions" or "TPMS Calibration". 
  4. Press and hold the appropriate button (like the "Check" button or trip-reset stalk) to activate the relearn mode. 
  5. The vehicle will prompt you to start the process. You will then need to use a TPMS activation tool to trigger each sensor, starting with the driver's front tire, until you hear a horn chirp. 
• Using a physical button (older models): Some older models have a physical button.
  1. Turn the ignition to the "On" position. 
  2. Locate the TPMS reset button, typically under the steering column. 
  3. Press and hold the button until the tire pressure light flashes three times. 
• Using tire pressure adjustments: In some cases, simply over-inflating the tires and then deflating them can reset the system. 
  1. Inflate each tire to 3 PSI above the recommended level. 
  2. Completely deflate each tire, including the spare if it has a sensor. 
  3. Inflate all tires to the correct pressure. 
• Using the key fob (some models): On some models with keyless entry, you can use the remote to activate the relearn mode. 
  1. Park the vehicle and turn the ignition to the "On" position. 
  2. Press and hold the "LOCK" and "UNLOCK" buttons on the key fob simultaneously for about five seconds. 
  3. Follow the on-screen prompts or use a TPMS activation tool on each tire as described above. 
• Using the battery (last resort): If all else fails, you can try disconnecting the battery.
  1. Disconnect the negative battery cable. 
  2. Turn the key to the "On" position and honk the horn for a few seconds to discharge any residual power. 
  3. Reconnect the battery. 

This video shows how to reset the tire pressure monitoring system on a 2014 Chevy Silverado: 53sBartec TPMSYouTube · Aug 13, 2014
Important considerations

• Before attempting a reset, always check your tires for punctures and ensure they have the correct air pressure, as low pressure is the most common cause of the TPMS light being on. 
• Your vehicle's owner's manual will have the most accurate information for your specific make and model. 
• If the light remains on after attempting a reset, there may be a problem with a sensor itself. 

How do I manually reset my TPMS sensor?

To manually reset your TPMS, first ensure all tires are inflated to the correct pressure, including the spare. Then, either hold down the TPMS reset button until the light blinks three times and drive for about 20 minutes, or disconnect the positive battery cable for a few seconds and reconnect it after honking the horn to discharge power. Many modern cars also allow you to reset the system through an option in the vehicle's infotainment or dashboard menu. 
This video demonstrates how to reset the TPMS light by using the infotainment system: 51sHondaYouTube · Aug 7, 2023
Method 1: Using the reset button or infotainment system

• Inflate all tires to the recommended pressure listed on the sticker inside the driver's side door jamb. 
• Locate the TPMS reset button, which is often under the steering wheel or in the glove box, or find the TPMS calibration option in your car's dashboard or infotainment system. 
• With the ignition in the "On" position (but the engine not running), press and hold the reset button until the TPMS warning light blinks three times, or select "Calibrate" in the menu. 
• Start the vehicle and drive for up to 20 minutes to allow the system to recalibrate. 

Method 2: Disconnecting the battery

• Make sure the car is off, then use a wrench to disconnect the positive (+) battery terminal. 
• Turn the car's ignition to the "On" position and honk the horn for about three seconds to drain any remaining power from the vehicle's electrical system. 
• Reconnect the positive battery cable. 
• Inflate your tires to the correct pressure, as this method may clear a warning light that came on after you correctly adjusted your tire pressure. 

Method 3: Driving to recalibrate

• If your car has a specific TPMS reset button, use it first as described in Method 1. 
• Drive at or above 50 mph for at least 10 minutes to allow the system to reset itself. 
• If your vehicle has an option in the onboard menu, use it to start the calibration process, then drive for a few minutes at over 20 mph. 

You can watch this video to learn how to program TPMS sensors without a tool for certain vehicles: 59sGregg FestoYouTube · Sep 12, 2022

How do you reset the TPMS on a Chevy Colorado?

To reset the TPMS on a Chevy Colorado, put the vehicle in "learn mode" via the Driver Information Center by holding the reset button on the steering wheel or turn signal stalk until the horn beeps twice and the dashboard indicates "learn mode". Then, use a TPMS relearn tool to activate each sensor, starting with the front-left tire, or, for a non-tool method, by deflating and reinflating the tires in the correct order.
 
Method 1: Using a TPMS relearn tool (recommended)

1. Enter learn mode: Turn the ignition to the "On" position without starting the engine. Press and hold the TPMS reset button on the steering wheel or stalk until the horn honks twice and the dashboard displays "Tire Learning Active". 
2. Activate front-left sensor: Place the TPMS relearn tool near the valve stem of the front-left tire. The tool will send a signal and the vehicle will honk once when the sensor is learned. 
3. Activate remaining sensors: Repeat the process for the other tires in the following order: front-right, rear-right, and rear-left. 
4. Complete the reset: After the last tire is learned, the vehicle will honk twice to indicate the process is complete. 

Method 2: Without a tool (requires deflating tires) 

1. Enter learn mode: Use your key fob to press and hold the LOCK and UNLOCK buttons at the same time for five seconds, or use the method above with the steering wheel buttons. 
2. Adjust tire pressure: Inflate each tire to 333 PSI over the recommended pressure, then completely deflate them. 
3. Inflate tires: Reinflate all tires to the correct pressure. 
4. Drive to reset: Drive at a speed of 505050 mph or higher for at least 10 minutes, or wait for the system to reset. 

If the light stays on

• If the light remains on after a successful reset, it could indicate a broken sensor or a low battery.
• If you see a flashing light, this almost always indicates a problem with a sensor.
• Take the vehicle to a professional for diagnosis and repair if the light does not turn off. 

How to relearn Chevy TPMS sensors?

Press and hold the keyless-entry fob transmitter's LOCK and UNLOCK buttons, at the same time, for about five seconds to start the TPMS learn mode. The horn sounds twice indicating the TPMS receiver is ready and in learn mode. This can also be performed using the turn signal arm and the driver information center.