How to reset TPMS on Chevy Volt 2017?

The Tire Pressure Monitoring System (TPMS) on a 2017 Chevy Volt is reset by inflating all tires to the recommended pressures, using the Driver Information Center (DIC) to perform a TPMS reset, and then driving to allow the system to relearn the sensor data. This method reflects the standard approach for this model and year, though exact menu wording can vary with software updates.

What TPMS is and why a reset might be needed

TPMS uses sensors in each tire to monitor air pressure and warn you if a tire is underinflated. A reset is often required after inflating tires to the correct pressures, rotating tires, or replacing sensors. Resetting the system tells the Volt to relearn the current tire pressures and sensor IDs so the warning light behaves correctly.

Step-by-step reset via the Driver Information Center

Below is a typical process using the car's built-in menu. The steps are intended to guide you through the most common, up-to-date method; wording may vary slightly by software version.

1. Put the ignition in the Run position with the engine off and the vehicle in Park.


2. Use the steering wheel controls to access the Vehicle Information menu, then navigate to Tire Pressure Monitor or TPMS settings.


3. Select Tire Pressure Monitor Reset and confirm if prompted.


4. Inflate all tires to the recommended cold pressures shown on the door placard (and include the spare if applicable).


5. Drive the vehicle at a steady speed for about 10 minutes to allow the TPMS to relearn the current sensor data.


6. Check the TPMS warning light; it should turn off once the relearn is complete. If the light remains on, recheck tire pressures and consider a dealership inspection if sensors or wiring are suspected faulty.

The reset performed through the DIC is intended to synchronize the system with the current tire pressures and sensor IDs. A successful reset is usually indicated by the TPMS light going out after the relearn drive.

Alternative method: If your Volt has a TPMS reset button

Some trims or software versions may include a physical TPMS reset button. If your vehicle has one, you can try this alternative method.

• Inflate all tires to the recommended pressures and center the vehicle in Park.


• Turn the ignition to the Run position (engine off).


• Press and hold the TPMS reset button until the TPMS warning light blinks three times, then release.


• Drive for about 10 minutes to complete the relearn cycle.

Note that not all 2017 Volt models include a dedicated TPMS reset button. If you don’t see a reset button, rely on the DIC method described above.

Troubleshooting and tips

If the TPMS light stays on after a reset and a proper relearn drive, consider the following:

• Double-check that all tires, including the spare if applicable, are at the correct cold pressures.


• Inspect for a damaged or leaking tire sensor or a dead sensor battery, which may require professional service.


• Ensure wheel and tire changes were done correctly, and that sensors weren’t damaged during service.


• If the light remains illuminated, visit a Chevrolet service center for a diagnostic relearn or sensor replacement.

In most cases, following the standard DIC reset procedure and a proper drive will reset the system without further intervention.

Summary

Resetting the TPMS on a 2017 Chevy Volt is typically accomplished by inflating all tires to the manufacturer-recommended pressures, using the Driver Information Center to perform a Tire Pressure Monitor Reset, and then driving to complete the relearn. If your vehicle has a TPMS reset button, you can use that method as an alternative. If the warning light persists after these steps, seek professional service to diagnose sensor or system faults. Regularly verifying tire pressures helps maintain accurate TPMS readings and vehicle safety.

Where is my TPMS reset button on my Chevy?

The TPMS reset button on a Chevy is often located under the steering wheel, but the procedure can also involve using the vehicle's driver information center (DIC) or a separate tool. For many models, there isn't a simple button to press; instead, you'll need to navigate the menu in the instrument cluster and follow the "relearn tire positions" prompts to reset the system, often with a special tool to activate each sensor. If you can't find it, consult your owner's manual.
 
This video shows how to reset the tire pressure monitoring system on a 2007-2013 Chevy Silverado: 1m1A Auto: Repair Tips & Secrets Only Mechanics KnowYouTube · Feb 15, 2019
Common reset procedures

• Using the driver information center (DIC): This is the most common method for newer models. 
  1. Turn the ignition to the "On" position (without starting the engine). 
  2. Use the vehicle's buttons or steering wheel controls to navigate the DIC until you find the "Tire Pressure" or "Vehicle Settings" menu. 
  3. Select "Relearn Tire Positions" or "TPMS Calibration". 
  4. Press and hold the appropriate button (like the "Check" button or trip-reset stalk) to activate the relearn mode. 
  5. The vehicle will prompt you to start the process. You will then need to use a TPMS activation tool to trigger each sensor, starting with the driver's front tire, until you hear a horn chirp. 
• Using a physical button (older models): Some older models have a physical button.
  1. Turn the ignition to the "On" position. 
  2. Locate the TPMS reset button, typically under the steering column. 
  3. Press and hold the button until the tire pressure light flashes three times. 
• Using tire pressure adjustments: In some cases, simply over-inflating the tires and then deflating them can reset the system. 
  1. Inflate each tire to 3 PSI above the recommended level. 
  2. Completely deflate each tire, including the spare if it has a sensor. 
  3. Inflate all tires to the correct pressure. 
• Using the key fob (some models): On some models with keyless entry, you can use the remote to activate the relearn mode. 
  1. Park the vehicle and turn the ignition to the "On" position. 
  2. Press and hold the "LOCK" and "UNLOCK" buttons on the key fob simultaneously for about five seconds. 
  3. Follow the on-screen prompts or use a TPMS activation tool on each tire as described above. 
• Using the battery (last resort): If all else fails, you can try disconnecting the battery.
  1. Disconnect the negative battery cable. 
  2. Turn the key to the "On" position and honk the horn for a few seconds to discharge any residual power. 
  3. Reconnect the battery. 

This video shows how to reset the tire pressure monitoring system on a 2014 Chevy Silverado: 53sBartec TPMSYouTube · Aug 13, 2014
Important considerations

• Before attempting a reset, always check your tires for punctures and ensure they have the correct air pressure, as low pressure is the most common cause of the TPMS light being on. 
• Your vehicle's owner's manual will have the most accurate information for your specific make and model. 
• If the light remains on after attempting a reset, there may be a problem with a sensor itself. 

How to reset TPMS on 2017 Chevy Volt?

To reset the TPMS on a 2017 Chevy Volt, put the car in accessory mode, then navigate to the tire pressure menu and start the relearn procedure. Use a TPMS relearn tool to activate each wheel's sensor, starting with the driver's side front and moving clockwise, until the car honks to confirm all sensors are relearned. After the relearn is complete, turn the car off and restart it to complete the process. 
This video demonstrates the TPMS reset procedure for a Chevrolet Volt: 55sIt’s Always Something DIYYouTube · Apr 2, 2022
Step-by-step guide

1. Enter accessory mode: Without your foot on the brake, press the Start/Stop button for five seconds until the car is in accessory mode. 
2. Navigate to the TPMS menu: Use the steering wheel controls to go to the "Tire Pressure" page on the driver information center. 
3. Start the relearn process: Press and hold the check mark button (or trip-reset stalk) for about five seconds until the DIC displays "Tire Learning Active" and the horn beeps twice. 
4. Activate the sensors: Using a TPMS relearn tool, place the antenna near the valve stem of each tire and press the button until the horn beeps, indicating that the sensor has been activated. 
   • Begin with the driver's side front tire. 
   • Move to the passenger's side front tire. 
   • Move to the passenger's side rear tire. 
   • Finish with the driver's side rear tire. 
5. Confirm completion: Once all four tires are activated, the car will honk twice to confirm the relearn is complete. 
6. Restart the vehicle: Turn the car off and then restart it. The TPMS light should be off and the tire pressures should be displayed. 

You can watch this video for a visual guide on how to reset the TPMS sensors in a Chevrolet Volt: 56sMike BurnsYouTube · Nov 10, 2019

What is the TPMS frequency for a 2017 Chevy Volt?

DLPRS-4, snap in programmable Tire Pressure Monitoring System (TPMS) sensor. Programmable to cover 314.9 MHz, 315 MHz and 433 MHz application. Maximum speed: 130 Miles per hour.

How do you reset the TPMS on a 2017 Chevy?

So it will go into service mode. And once you're in service mode hit the uh arrows to scroll to the tire pressure. And then hold the check mark. Button. So just And now it says tire learning active.