What is the lug nut torque on a 2008 Toyota Yaris?
The lug nuts on a 2008 Toyota Yaris should be torqued to 76 ft-lbs (103 N·m) for most factory-equipped wheel configurations. This is the standard specification used by Toyota for the vehicle’s wheel fasteners, but always verify against your specific vehicle configuration in the owner’s manual or service manual.
Understanding the torque specification
Torque specifications ensure the wheel is securely attached without over-tightening, which could damage studs or brake components. Variations can occur due to aftermarket wheels, different lug nut sizes, or the use of wheel spacers. Always confirm the exact figure for your particular setup.
Official spec and where it appears
For the 2008 Yaris, Toyota’s typical service documentation lists 76 ft-lbs (103 N·m) as the standard lug nut torque. This applies to common factory wheels with standard lug nuts. If your vehicle has aftermarket wheels, different lug nuts, spacers, or a non-standard setup, consult the service manual or wheel manufacturer guidelines for the correct torque.
Practical torque and safety notes
Use a calibrated torque wrench and tighten in a star pattern to ensure even clamping. Do not apply lubricants to lug nuts unless the manual specifically calls for it, as lubricants can reduce the effective clamping force. After installation, recheck torque after a short drive (typically 50–100 miles or 80–160 kilometers) to account for seat-in and potential settling.
To help you apply the spec correctly, follow these steps:
- Prepare the vehicle: park on level ground, chock wheels, and ensure the vehicle is stable. Clean lug nuts and studs if needed.
- Hand-tighten in a star pattern to seating without cross-threading.
- Torque to 76 ft-lbs (103 N·m) using a calibrated torque wrench, in the same star pattern, until the wrench clicks.
- After initial drive, recheck torque in the same star pattern to confirm it remains at spec.
Following these steps helps ensure even loading, proper wheel retention, and reduces the risk of lug nut or wheel problems.
In summary, the standard lug nut torque for a 2008 Toyota Yaris is 76 ft-lbs (103 N·m) for typical factory wheel setups. Always consult your manual for any exceptions related to aftermarket wheels, lug nut sizes, or spacers.
Summary
The 2008 Toyota Yaris generally requires lug nuts to be torqued to 76 ft-lbs (103 N·m). Use a torque wrench, tighten in a star pattern, avoid lubricants unless specified, and recheck torque after a short break-in period. Verify with the owner’s manual or service manual if you have aftermarket components or non-standard hardware.
What is the torque on the Yaris wheel bolts?
GR Yaris GR Yaris Wheel Nut Torque Setting - 103nm.
What size are the lug nuts on a 2008 Toyota Yaris?
13/16" Hex
Check if this fits your vehicle. Notes: Nut. 12mm x 1.50 Thread Size, 13/16" Hex.
What is the torque spec for the lug nuts on a 2008 Toyota Yaris?
For the 2008 Toyota Yaris, torque rear hub assembly bolts to the manufacturer's spec (typically around 76 ft-lbs). Wheel lug nuts should be tightened in a star pattern to about 76 ft-lbs as well.
What is the torque on Toyota lug nuts?
Toyota lug nut torque varies by model and year, but a common specification is 80-85 ft-lbs for many models from the late 1980s to the early 2000s. For newer and larger vehicles, the torque can be higher, such as 100 ft-lbs for some Tundras and Sequoias or even 113 Nm (83.3 ft-lbs) for newer Tacomas. Always consult your vehicle's owner's manual for the precise specification.
This video explains how to torque lug nuts on a Toyota Tacoma: 1mTRD TakeoverYouTube · Jan 23, 2024
Common specifications by model year
- Avalon, Camry, Corolla, RAV4, Sienna: Most models from the late 1980s to the early 2000s are typically around 80 ft-lbs. Newer RAV4 models (2006-2023) are often around 76 ft-lbs.
- Tacoma: Torque is 85 ft-lbs for many models from the mid-1990s to mid-2000s, while newer models can be 113 Nm (83.3 ft-lbs).
- Tundra: Torque varies significantly, with some models requiring 150 ft-lbs and others 85 or 90 ft-lbs depending on the year.
- 4Runner: 80-85 ft-lbs is common for many models, but a 2019 model with aluminum rims requires 76 ft-lbs, while steel rims require 83 ft-lbs.
- Highlander, Venza: 80 ft-lbs for many models, but a 2009 Venza manual specifies 76 ft-lbs.
Important considerations
- Consult your owner's manual: This is the most reliable source for your specific vehicle's torque specifications.
- Check with tire size: Even within the same model, torque requirements can vary based on whether the vehicle has factory or aftermarket wheels, according to JustAnswer.
- Retorque after 50-100 miles: It is good practice to re-torque lug nuts after driving a short distance, especially after a tire change.
- Do not lubricate threads: Never apply grease or lubricant to the threads of the lug nuts or bolts, as this can cause them to be over-tightened and cause damage.
