What is the torque on the axle nut on a Dodge Ram?
The torque on the axle nut of a Dodge Ram is an important factor to consider when maintaining or servicing the vehicle's suspension and drivetrain components. Proper torque specification ensures the axle nut is tightened to the correct tension, preventing potential issues such as wheel bearing failure or uneven tire wear.
Determining the Correct Torque Specification
The recommended torque for the axle nut on a Dodge Ram can vary depending on the specific model year and configuration of the vehicle. The typical torque range for a Dodge Ram axle nut is between 200 to 300 ft-lbs (270 to 405 Nm).
It is crucial to refer to the manufacturer's recommended torque specification, which can be found in the vehicle's owner's manual or service documentation. Applying the correct torque ensures the axle nut is tightened to the proper tension, preventing potential issues with the wheel bearings, differential, or other drivetrain components.
Factors Affecting Axle Nut Torque
Several factors can influence the required torque for the Dodge Ram axle nut, including:
- Vehicle model and year
- Axle type (front or rear)
- Presence of a locking differential
- Wheel bearing design and specifications
- Lubricant used in the axle assembly
It is essential to consult the appropriate service information for your specific Dodge Ram model to ensure the axle nut is tightened to the manufacturer's recommended torque specification.
Properly Tightening the Axle Nut
To properly tighten the axle nut on a Dodge Ram, follow these steps:
- Ensure the vehicle is securely supported, either on jack stands or a lift, to allow access to the axle nut.
- Clean the axle shaft and nut threads to remove any dirt, debris, or corrosion.
- Apply a thin coat of the recommended lubricant to the axle shaft and nut threads.
- Use a torque wrench to tighten the axle nut to the manufacturer's specified torque value.
- Recheck the torque after the initial tightening to ensure it remains within the recommended range.
Properly tightening the axle nut is crucial for the safe and reliable operation of your Dodge Ram. Failure to follow the manufacturer's torque specifications can lead to premature wear or failure of the wheel bearings, differential, or other drivetrain components.
What is the torque spec for the axle nut on a 2016 Dodge Ram?
Tighten axle nut to final torque of 263 ft. lbs. Dodge Mechanic: Ron Z.
What is the wheel nut torque specifications?
New wheels should be re-torqued after the first 50 to 100 driving miles.
| Hardware Bolt or Stud Size | Typical Torque Range in Ft/Lbs | Minimum Number of Turns of Hardware Engagement |
|---|---|---|
| 14 x 1.25 mm | 85 - 90 | 9 |
| 7/16 in. | 70 - 80 | 9 |
| 1/2 in. | 75 - 85 | 8 |
| 9/16 in. | 135 - 145 | 8 |
What is the torque on the rear axle hub nut on a 2014 Ram 5500?
330 Nm (243 ft. lbs.)
What is the torque of a Dodge Ram?
2023 Ram 1500 Engine Options & Performance
| Engine | 3.6L Pentastar V6 | 5.7L HEMI V8 |
|---|---|---|
| Horsepower | 305 HP | 395 HP |
| Torque | 273 lb.-ft. | 410 lb.-ft. |
What is the torque on the axle nut on a Dodge Ram 2500?
Tighten the spindle nut to 149 ft-lbs 21. Rotate the axle 5 to 10 times to seat the hub bearing 22. Tighten the spindle nut to a final torque of 263 ft-lbs 23.
Do you need a torque wrench for axle nut?
Avoid Overtightening – Use the Right Tool
Many technicians use an impact gun when installing an axle nut on a wheel hub bearing which not only overtightens the bearing but can also cause premature wear to the hub assembly. MOOG recommends using a torque wrench to tighten the axle nut accurately.
How much torque for axle nut on 2019 Dodge Ram?
185 ft-lbs
Install the center hub nut. Torque to 185 ft-lbs.
What is the torque spec for Ram 1500 wheels?
When it comes to RAM 1500 wheel nut torque, for flanged nuts, recommendations are 140 lb-ft., while for coned-type nuts, recommendations are 130 lb-ft. It is also advised that you check on your RAM 1500 lug nut torque after driving an initial 80-160 km following wheel installation.
What should the torque be on an axle nut?
On some wheel bearings sets and hub units, the axle nut secures the outer flange to a CV joint or stub axle. As the nut is tightened, it pulls the flange and axle together to set the preload of bearings. These axle nuts will have specifications as low as 130-foot pounds and as high as 300-foot pounds.
Do I need a torque wrench for an axle nut?
OEM and bearing manufacturers always recommend using a torque wrench for installation. Using an impact to “run down” the axle nut can cause the assembly to be over-torqued.
