What is the torque spec for the brake calipers on a 2010 Honda Accord?

Front brake caliper mounting bolts: 22 N·m (16 ft-lb). Rear brake caliper mounting bolts: 23 N·m (17 ft-lb).

For the 2010 Honda Accord, torque specs for brake calipers can vary by trim and whether you’re dealing with front discs or rear discs. The figures below reflect commonly cited values from the Honda service manual for typical front and rear caliper installations on 2010 Accords. Always verify with the official manual for your exact VIN and configuration before servicing.

Torque specs by caliper location

The following values are provided as a baseline reference for common 2010 Accord brake setups. When performing brake work, use a calibrated torque wrench and recheck torque after a short road test if advised by the manual.

• Front brake caliper mounting bolts: 22 N·m (16 ft-lb).


• Rear brake caliper mounting bolts: 23 N·m (17 ft-lb).

These values pertain to the bolts that secure the caliper to the mounting bracket (front) and to the knuckle (rear) in typical configurations. If you are replacing other components (such as caliper brackets or slide pins), different torque specifications may apply, and you should consult the service manual for those specific fasteners.

Notes and installation tips

When performing brake caliper work, follow these cautions to ensure proper installation and safety:

• Clean all bolt threads and mating surfaces before reassembly. Do not skip cleaning, as contamination can affect torque accuracy and braking performance.


• Use the correct lubricant on caliper pins as specified by Honda (typically silicone-based brake grease); do not use general-purpose lubricants on sliding pins.


• Do not reuse damaged or overtightened fasteners. If you replace caliper bolts, use OEM-recommended parts.


• After reassembly and a brief test drive, recheck the caliper bolt torque if the manual directs it.

Summary

For a typical 2010 Honda Accord, expect front caliper mounting bolts to be torqued to about 22 N·m (16 ft-lb) and rear caliper mounting bolts to about 23 N·m (17 ft-lb). Always confirm exact values in your vehicle’s service manual for your specific trim and VIN, and follow Honda’s installation procedures to ensure safe, effective braking performance.

What is the torque spec for brake caliper bolts?

Torque specs for brake caliper bolts vary significantly depending on the vehicle, but here are some general guidelines: caliper mounting or bracket bolts are typically 70–100 ft-lbs, while caliper slide/guide pin bolts are often 18–35 ft-lbs. Always use your vehicle's specific service manual for the correct values, as they are crucial for safety. 
Caliper mounting/bracket bolts

• What they do: These bolts attach the caliper bracket to the wheel knuckle or spindle. 
• General torque range: 707070 to 100 ft-lbs100 ft-lbs100 ft-lbs. 
• Example: A 2003 Silverado specifies 85−95 ft-lbs85 minus 95 ft-lbs85−95 ft-lbs for caliper bracket bolts. 

Caliper slide/guide pin bolts

• What they do: These bolts hold the caliper to the bracket and allow it to slide to center itself on the rotor. 
• General torque range: 181818 to 35 ft-lbs35 ft-lbs35 ft-lbs. 
• Example: A 2011 Honda Accord specifies 17 ft-lbs17 ft-lbs17 ft-lbs for the rear and 37 ft-lbs37 ft-lbs37 ft-lbs for the front guide pin bolts. 

Other brake-related bolts

• Banjo bolt (brake line to caliper): Torque to about 18 ft-lbs18 ft-lbs18 ft-lbs.
• Bleeder screw: Torque to a low value, around 8 ft-lbs8 ft-lbs8 ft-lbs. 

Important considerations

• Always use the service manual: Torque specifications are not universal and must be obtained from your specific vehicle's service manual for safety. 
• Two types of bolts: Be sure to differentiate between the larger caliper mounting/bracket bolts and the smaller caliper slide/guide pin bolts, as they have very different torque values. 
• Use a torque wrench: Using a torque wrench is essential for ensuring the bolts are tightened to the correct specification. 
• Clean and lubricate: Clean threads before applying new bolts and lubricate slide pins with the manufacturer-specified grease to prevent sticking. 

What is the torque setting for a Honda Accord?

Honda Accord torque specs vary significantly by model year and specific component, so it's crucial to consult the service manual for your exact vehicle. For example, cylinder head bolts on many 4-cylinder Accords are torqued to 29 ft-lbs, followed by two 90-degree turns, while the 2010 Accord's 3.5L V6 has different specs for the upper intake manifold (22 lb-ft), lower intake manifold (15 lb-ft), and spark plugs (13 lb-ft). 
This video demonstrates the cylinder head torque specifications and sequence for a Honda K24 2.4L engine: 1mMotorCarNutYouTube · Apr 27, 2024
Examples of specific component torque values:

• 2004 Accord 4-Cylinder DOHC Head: 29 ft-lbs, then 59 ft-lbs, then a 90-degree turn. 
• 2008-up Accord 2.4L VTEC Cylinder Head: Torque in sequence to 29 ft-lbs, then two 90-degree turns (one 90-degree turn for new bolts). 
• 2010 Accord 3.5L V6 Intake Manifold:
  • Upper: 22 lb-ft. 
  • Lower: 15 lb-ft. 
• 2010 Accord 3.5L V6 Spark Plugs: 13 lb-ft. 
• 2010 Accord 3.5L V6 Oil Drain Bolt: 33 lb-ft. 
• 2008 Accord 3.5L V6 Rocker Arm Shaft: Typically 12-15 ft-lbs. 
• 2000 Accord Camshaft Cap: 16 ft-lbs for both 8mm and 6mm bolts. 

Important considerations:

• Always use a calibrated torque wrench: for accuracy. 
• Follow the specified tightening sequence: to ensure even pressure and prevent warping. 
• Clean threads: before starting any torque procedures. 
• Consult the service manual: for your specific model year and engine for precise values and sequences. 
• Over-tightening can cause damage, while under-tightening can lead to leaks or component failure. 

You can watch this video to learn how to replace the rear hub bearing on a Honda Accord (2013-2017), including the torque specs: 50sRB The MechanicYouTube · Sep 15, 2022

What is the torque on a 2013 Honda Accord caliper?

For the 2013 Honda Accord LX, front brake caliper bolts typically torque to 79 ft-lbs, rear caliper bolts to 33 ft-lbs. Proper torque ensures even pad pressure and prevents warping. Always clean bolt threads and use a calibrated torque wrench.

What is the torque on the caliper bolts on a 2010 Honda Accord?

Torque your caliper bracket bolts to 80 foot-lbs repeat for the top install your brake pads make sure that your back pad has the squeak tab on the.