What kind of oil does a 2014 Acura TL take?
The 2014 Acura TL usually requires 5W-20 synthetic oil, with a total capacity of about 5.5 quarts when changing the oil and filter. This specification supports reliable cold starts and engine protection, but you should always confirm exact requirements in the owner's manual for your climate and driving conditions.
Recommended oil type and viscosity
The 3.5-liter V6 engine in the 2014 TL is designed for high-quality motor oil that meets current API standards. For most drivers, 5W-20 full synthetic oil is the standard recommendation, with 5W-30 as an alternative only if your manual permits it or if you operate in extreme heat or under heavy load.
Climate and usage considerations
Viscosity choices can vary by climate and driving style. While 5W-20 covers typical conditions well, hotter climates or frequent strenuous driving may justify 5W-30, provided your vehicle’s manual allows it. Always consult the manual or your dealer for climate-specific guidance.
Here are the common oil options that satisfy many 2014 TL owners and service centers:
- 5W-20 full synthetic motor oil (recommended for most driving conditions)
- 5W-20 synthetic blend (acceptable if full synthetic is unavailable)
- 5W-30 full synthetic motor oil (acceptable only if specified by the manual for your climate or usage)
Conclusion: For everyday driving in temperate regions, 5W-20 full synthetic is the standard choice; 5W-30 is typically reserved for specific climates or heavy-load conditions as allowed by the owner's manual.
Oil capacity and change intervals
The 2014 TL’s engine oil capacity with the filter is about 5.5 quarts (5.2 liters). After installing a new filter, fill to the specified level and recheck with the dipstick. Change intervals are guided by the vehicle’s maintenance minder and driving conditions, typically ranging from roughly 5,000 to 7,500 miles for normal driving, with shorter intervals under severe conditions or harsh service.
Steps to check and perform an oil change
Following a standard process helps ensure accurate levels and proper sealing during an oil change:
- Run the engine briefly, then park on a level surface and turn off.
- Wait a few minutes for oil to settle, then remove the dipstick and wipe clean.
- Drive or lift the vehicle to access the oil drain plug safely, place a drain pan, and remove the plug to drain old oil.
- Replace the oil filter, reinstall the drain plug, and pour in the recommended amount of oil (about 5.5 quarts).
- Check the oil level on the dipstick again and top up if needed; start the engine and look for leaks.
- Dispose of used oil responsibly and note the date and mileage for maintenance records.
Conclusion: Use the maintenance minder and owner’s manual to determine exact intervals for your situation, but a typical change cadence sits around every 5,000–7,500 miles under normal driving conditions.
What to buy and how to verify compatibility
To ensure the best protection and performance, select oils that meet or exceed API SN (or newer) and ILSAC GF-5 standards, with a viscosity of 5W-20 as the default. Whenever possible, opt for Acura- or Honda-branded motor oil or a reputable equivalent that is explicitly rated for the 3.5L V6 found in the 2014 TL. Use a high-quality oil filter designed for this engine.
- 5W-20 synthetic motor oil (primary recommendation)
- 5W-20 synthetic-blend if full synthetic is unavailable
- Appropriate oil filter for the 3.5L V6
- Basic tools: funnel, drain pan, and a torque-rated filter wrench
Conclusion: Following the specified oil type, capacity, and filter recommendations helps maintain the TL’s performance and longevity. Always verify details against your vehicle’s manual or a trusted Acura service professional.
Summary
In brief, the 2014 Acura TL typically takes 5W-20 synthetic oil, with an oil capacity of about 5.5 quarts including the filter. This recommendation supports reliable cold starts and engine protection. Climate, driving style, and the vehicle’s maintenance minder influence the exact oil choice and change interval, so consult the owner’s manual for vehicle-specific guidance. Regular checks and using a quality oil and filter will help keep the TL running smoothly.
Can I use 5w30 instead of 5W20 in my Acura?
Everywhere else in the world besides the US, depending on climate, Acura/Honda suggests different viscosities in our J32/J35 engines, ranging from 5w20-10w40. These engines were designed to run on 5w30. You aren't going to hurt anything. Especially if you live somewhere hot.
What kind of oil does a 3.7 L V6 take?
Capacities and Specifications - 3.7L
| Name | Specification |
|---|---|
| Recommended motor oil (U.S.): Motorcraft® SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP | WSS-M2C945-A |
| Recommended motor oil (Canada): Motorcraft® SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12 | WSS-M2C945-A |
What oil does a 2014 Acura TL take?
If you own a TL between model years 2004-2014, your engine's recommended oil is 5W-20, a fully synthetic oil; if your Acura TL model is even older, from model years 1999-2003, the most versatile and safe oil to use in your engine is 5W-30 synthetic oil.
What oil does an Acura TL take?
Information
| CL | 2003: 5W-20 (S/UFS), topped off with 0W-20 (UFS) |
|---|---|
| TL | 2003 3.2Liter: 5W-20 (S/UFS) 2004-2008: 5W-20 (S/UFS), topped off with 0W-20 (UFS) 2007-2011 3.5Liter: 5W-20 (S/UFS), topped off with 0W-20 (UFS) 2012-2014: 0W-20 (UFS) 2009-2014 3.7Liter: 5W-20 (S/UFS) |
| TLX | 2015-2020: 0W-20 (UFS) |
