What kind of oil does a Avenger 220 take?
The Bajaj Avenger 220 typically requires a mineral motorcycle engine oil with a viscosity around 20W-40 and a total fill of about 1 liter. Always confirm the exact spec from your model’s owner’s manual or Bajaj service notes, as variations can exist between trims and regions.
Oil type and viscosity recommendations
Use the following guidance as a baseline. The right oil protects the engine in hot climate riding, city traffic, and long trips.
- 20W-40 mineral engine oil (API SG/SH or higher) — standard choice for most Avenger 220 models in hot climates.
- 15W-40 or 20W-50 — may be suitable in cooler climates or for heavy use; consult your manual for your exact variant.
- Motorcycle-specific oil (synthetic or synthetic blend) — acceptable if it meets API SN or newer and is compatible with air-cooled engines; may offer longer drain intervals and improved cold starts.
Always use oil intended for motorcycles (not automobile engine oil) and avoid mixing oils or additives unless advised by the manufacturer.
Oil capacity and maintenance tips
Knowing the oil capacity helps you prepare the right amount of lubricant and plan changes. The Avenger 220 typically holds around 1 liter of engine oil; exact capacity depends on the variant and whether the bike uses an oil filter.
- Consult the owner's manual for the exact capacity and the oil filter situation for your model.
- Check the oil level with the dipstick or sight glass when the engine is cold, and add gradually to the recommended level.
- Change intervals: with mineral oil, expect around 5,000–7,500 km (3,000–4,700 miles); synthetic oils may extend this to around 10,000 km (6,200 miles) or more, depending on usage and conditions.
Regular oil level checks and adherence to the manufacturer’s schedule help maintain engine longevity. If in doubt, consult a Bajaj service center or refer to official documentation for your exact model year.
Summary
For most Bajaj Avenger 220 models, the baseline oil choice is a mineral 20W-40 motorcycle oil, about 1 liter of oil. Alternatives include lighter or heavier viscosities depending on climate and usage, or synthetic blends that are compatible with motorcycle engines. Always verify with the owner's manual and use motorcycle-specific oil rather than car oil.
What kind of oil goes in a Dodge Avenger?
The recommended oil for a Dodge Avenger is typically 5W-20, especially for the 4-cylinder engine. Some models, like the 2010, might also use 5W-30. It is best to consult your owner's manual to confirm the specific type and weight, and always use an oil that meets the API SN or higher standards and is compatible with your engine, such as a full synthetic or synthetic blend.
Key details
- Viscosity: 5W-20 is commonly specified, but check your owner's manual, as some models may use 5W-30.
- Oil type: Full synthetic or a synthetic blend is recommended for best performance and protection, especially for high-mileage engines.
- Specifications: Look for oil that meets or exceeds API SN or higher standards, and specifically meets the Chrysler MS-6395 requirement.
- Oil filter: Always replace the oil filter with each oil change.
- Capacity: The 2.4L engine typically takes 4.5 quarts of oil with a filter change.
Can I use 15W-40 engine oil for a bike?
Short answer: No -- do not use diesel engine 15W‐40 oil in a 50cc motorcycle unless the oil's label explicitly states it's suitable for small four-stroke motorcycle engines (API/ACEA plus JASO MA/MA2). Using the wrong oil risks clutch slippage, poor lubrication, increased wear, and possible engine damage.
What kind of oil does a Kawasaki 220 take?
Standard 10W-40 Oil Change Kit compatible with 1988-2002 Kawasaki BAYOU 220.
Which engine oil is used in the Avenger 220?
Max Pro Max Power Plus SAE - 20W50 4 Stroke Motorcycles Engine Oil, 1L for Bajaj Avenger 220 DTS-i : Amazon.in: Car & Motorbike.
