What lug size is a Dodge Charger?

Chargers built on the LX platform typically use a 5x115 mm bolt pattern with 14 mm wheel studs and 21 mm lug nuts; the center bore is about 71.5 mm. These specs cover the majority of modern Chargers, but some trims or aftermarket wheels can differ. Always verify with the door jamb placard or owner’s manual for your exact vehicle.

The question encompasses the standard bolt pattern, wheel studs, lug nuts, and hub dimensions that determine wheel compatibility. This article outlines the core specifications, notes common variations across popular Charger models (base, RT, Scat Pack, Hellcat), and explains how to confirm the correct sizes for your specific car.

Bolt pattern and hub specs

Below are the key measurements used to determine wheel compatibility for most Dodge Chargers. Use the list to compare against your current wheels or when shopping for replacements.

• Bolt pattern: 5 x 115 mm (five lug holes on a 115 mm bolt circle)


• Center bore: 71.5 mm


• Wheel stud diameter: 14 mm


• Thread pitch: typically M14 x 1.5


• Lug nut type: conical seat (60-degree)


• Factory lug nut socket size: 21 mm

These measurements are the standard baseline for most LX-platform Chargers. If you install aftermarket wheels, verify both the bolt pattern and center bore to ensure proper fit and hub-centric alignment.

Common Charger models and years that use these specs

Most Dodge Chargers produced on the LX platform from 2005 onward (including SXT, RT, Scat Pack, and Hellcat variants) use the 5x115 mm bolt pattern with 14 mm studs and 21 mm lug nuts. Some aftermarket setups or special editions may adjust lug hardware, so confirm against your VIN and wheel specification when in doubt.

Lug nuts, torque, and installation notes

Understanding the lug hardware and proper installation helps prevent wheel issues. The following points cover typical practices and what to check beyond the basic measurements.

• Torque specification: commonly around 100–120 ft-lbs (135–162 N·m), but always confirm for your exact model/year in the owner's manual.


• Seat type: factory hardware uses a 60-degree conical seat; aftermarket lugs must match the seat style to seat correctly.


• Installation sequence: tighten in a star pattern to ensure even seating and avoid warping the brake rotor or drum.

Using the correct torque and seat type is essential for safety and wheel longevity. If you’re changing wheels or upgrading, consult the wheel manufacturer’s specs and consider professional installation if you’re uncertain.

Summary

The Dodge Charger generally follows a 5x115 mm bolt pattern with 14 mm wheel studs and 21 mm lug nuts, plus a center bore of about 71.5 mm. While these specs apply to most LX-platform Chargers, always verify your specific vehicle’s measurements on the door jamb placard or in the owner’s manual, especially when swapping to aftermarket wheels. Proper torque and lug nut seating are crucial for safe wheel mounting.

What size socket is a 2018 Dodge Charger lug nut?

14 mm x 1.50 thread size, 7/8" hex, 1.78" length.

What size are the lug nuts on a Dodge Charger?

14 mm x 1.50 thread size, 7/8" hex.

What size are Dodge lug nuts?

The most common Dodge lug nut size is M14x1.5, especially for modern models like the Ram 1500 and Charger. However, older models and certain trucks may use 9/16-18 or 1/2-20. It is essential to check the specific vehicle's requirements, as the size, seat type (such as conical), and hex size can vary.
 
Common lug nut sizes

• M14x1.5: This is the most prevalent size for newer models like the Ram 1500, Charger, and Durango. 
• 9/16-18: Common on older Dodge and Ram trucks from approximately 1994–2011. 
• 1/2-20: Also found on some older vehicles. 

Other important specifications

• Hex Size: The size of the tool needed to tighten the lug nut can vary. Common hex sizes include 7/8" (22mm) and 13/16" (21mm). 
• Seat Type: The lug nut must match the wheel's seat type. A common type for Dodge is the 60-degree conical or acorn seat. 

How to confirm your vehicle's lug nut size

• Consult your owner's manual: The manual will have the most accurate information for your specific vehicle.
• Measure your existing lug nuts: You can measure the diameter and thread pitch of a lug nut you already have. 
• Use an online lookup tool: Many auto parts websites have a tool where you can enter your vehicle's year, make, and model to find the correct lug nuts. 

What size socket for Dodge Challenger lug nuts?

The correct lug nut socket size for a Dodge Challenger is 13/16 inch or 22mm, which are equivalent. It is recommended to use a 12-point, 6-point socket to avoid damaging the lug nuts. 
Socket size

• 13/16" or 22mm: This is the standard size for both the stock and aftermarket lug nuts. 
• Note: While 13/1613 / 1613/16 inch and $22$mm are often used interchangeably, a $22$mm socket can sometimes feel a bit loose on a 13/1613 / 1613/16 inch nut, or a 13/1613 / 1613/16 inch socket can be tight on a $22$mm nut, depending on the manufacturing tolerances. 

Important tips

• Use a 6-point socket: A 6-point socket provides better grip and is less likely to strip the lug nuts compared to a 12-point socket. 
• Use a non-marring socket: If you are working with rims that you want to protect, consider using a socket with a protective coating to prevent scratches. 
• Apply the correct torque: Always use a torque wrench to tighten the lug nuts to the manufacturer's specification (e.g., 111 ft-lbs for a 2023 Dodge Challenger Hellcat).