What oil does a Ford F-250 6.2 take?

The 6.2-liter gasoline V8 in many Ford F-250 Super Duty pickups typically uses 5W-20 oil, and the engine holds about 6 quarts with a filter. Use a Ford-approved oil that meets WSS-M2C930-A (or the current equivalent) and follow your manual for exact change intervals.

Oil choice matters for protection, fuel economy, and warranty. Since Ford occasionally updates specs and there can be year-to-year differences, always confirm the exact requirement for your specific truck by checking the owner’s manual or the under-hood data label, especially if you tow heavy loads or operate in extreme climates.

Oil Type and Capacity for the 6.2L V8

Below are the standard guidelines you’ll typically find in Ford documentation for the 6.2L V8 in the F-250. The precise figure can vary by model year, so verify against your vehicle’s documentation.

• 5W-20 synthetic blend or full-synthetic motor oil that meets Ford specification WSS-M2C930-A or the current equivalent. This is the recommended grade for factory-fill and routine maintenance.


• Oil capacity is approximately 6 quarts (about 5.7 liters) with a filter change. Exact capacity may vary slightly by year and configuration, so check the dipstick and manual.


• Ensure the oil you buy is Ford-approved for the 6.2L; using non-approved oil can affect lubrication and warranty coverage. When Ford updates specs, use the latest approved version.

Conclusion: For most 6.2L F-250 models, plan on about 6 quarts of 5W-20 that meets Ford M2C930; always confirm with your specific year’s manual or label to avoid misalignment with updates.

Maintenance and Verification

To keep your 6.2L engine in good condition, follow these checks and best practices when shopping for oil and scheduling changes.

• Refer to the owner's manual and the under-hood oil cap label for your exact grade and capacity for your model year, as Ford may update specs.


• Follow Ford’s recommended change intervals, which may be guided by the oil life monitor and vary with driving conditions, towing, and climate.


• Choose oil that meets Ford’s specification (5W-20, M2C930 or newer) and select synthetic blend or full synthetic depending on usage; synthetic is generally preferable for heavy use or extreme temperatures.

Conclusion: With the right oil grade and amount, you’ll maintain proper lubrication and protection for the 6.2L engine under typical and demanding conditions alike.

Why the oil specification matters

Using the correct oil helps protect engine components, maintain performance, and safeguard the warranty. The 6.2L is designed around 5W-20 in normal service, so sticking to Ford-approved oil ensures proper viscosity and additive package.

Summary

In short, the Ford F-250 with the 6.2L gas engine generally requires 5W-20 oil (synthetic blend or full synthetic) and about 6 quarts of oil with a filter, meeting Ford specification WSS-M2C930-A (or newer). Always verify the exact requirements for your year and trim in the owner’s manual or on the under-hood label, and choose a Ford-approved oil to ensure proper protection and warranty compliance.

What kind of oil does a f250 6.2 take?

The correct oil for a Ford F-250 with a 6.2L engine is SAE 5W-30, though the recommended oil type can vary by model year, so always check your owner's manual. For models from 2016-2022, some resources recommend SAE 5W-20 or SAE 5W-30 depending on the vehicle's specific requirements. You should also check your owner's manual for the correct oil specification, which is typically WSS-M2C946-A or WSS-M2C961-A1.
 
For 2016-2022 Ford F-250 6.2L engines:

• Oil type: SAE 5W-30 or SAE 5W-20 (check your owner's manual for your specific model) 
• Oil specification: WSS-M2C946-A or WSS-M2C961-A1 
• Capacity: 7 quarts (including filter) 

For 2011-2015 Ford F-250 6.2L engines:

• Oil type: SAE 5W-20 (some sources suggest 5W-30 may also be acceptable)
• Oil specification: WSS-M2C945-B1
• Capacity: 7 quarts (including filter) 

For extreme cold climates (below -22∘Fnegative 22 raised to the composed with power cap F−22∘𝐹 or -30∘Cnegative 30 raised to the composed with power cap C−30∘𝐶):

• Use SAE 0W-30 oil that meets the WSS-M2C963-A1 specification to improve cold starts. 

Can I use 5W30 instead of 5W20 in my Ford?

Yes, you can likely use 5W-30 instead of 5W-20 in your Ford, especially if it's an older vehicle, as they have similar cold-start viscosity and 5W-30 offers slightly thicker protection at operating temperature. While Ford sometimes recommends 5W-20 for fuel economy, switching to 5W-30 is unlikely to cause harm, particularly in higher-mileage engines, and may provide better protection under stress. 
Key differences

• Cold starts: Both 5W-20 and 5W-30 have the same viscosity (thickness) when the engine is cold. 
• Hot operation: At high temperatures, 5W-30 is thicker than 5W-20, offering a thicker film for protection, especially in high-stress or high-heat conditions. 
• Fuel economy: The switch to 5W-20 in some newer models was largely driven by fuel economy regulations, and many older engines were originally designed for 5W-30. 

What to consider

• Check your owner's manual: The most accurate advice will always be in your vehicle's owner's manual. 
• Engine age and mileage: Older or higher-mileage engines may benefit more from the thicker 5W-30 oil. 
• Driving conditions: If you frequently tow, haul heavy loads, or drive in very hot weather, 5W-30 can provide better protection. 
• Potential downsides: Using a thicker oil may slightly decrease fuel economy. In some specific cases with newer engines, it could potentially lead to a minor increase in noise, so it's always best to start with the manufacturer's recommendation if possible, according to a Reddit post. 

In conclusion, using 5W-30 instead of 5W-20 is generally considered a safe and acceptable alternative for most Ford vehicles.

What oil goes in a F250 Super Duty?

2025–2023 F-250 (Current Generation)
6.7L Power Stroke Diesel: Ford's primary recommendation is SAE 10W-30 meeting spec WSS‑M2C171‑F1. In extreme cold (‑22°F / ‑30°C) you can move to 0W‑40, and for severe duty or biodiesel blends, 5W‑40 (or even 15W‑40) is approved as noted in the manual and Motorcraft chart.

What oil is best for 6.2 V8?

It can be any 0W-40 oil with the dexosR specification, which includes oils with Mobil 1, Mobil 1 FS, and Mobil 1 ESP X4 branding. GM believes this oil will help prevent the problems identified with the L87 engine in 2021-2024 trucks and SUVs.