What size are the lug nuts on a Ford EcoSport?
The lug nuts on most Ford EcoSport models are M12 x 1.75 with a 60-degree conical seat and a 19mm socket size, but exact specs can vary by year and market.
The EcoSport has been produced for multiple regions and model years, with wheel configurations and fastener specs that can change over time. For precise sizing, always consult the owner's manual, your vehicle’s door jamb data plate, or a Ford dealer, especially before purchasing replacement fasteners or wheels.
Common specs and what to know
Before listing the typical sizing, here is an overview of the factors that affect lug nut specs on the EcoSport.
- Thread size and pitch: The diameter is typically 12 millimeters, but the thread pitch can be either 1.5 or 1.75, depending on year and market.
- Seat type: Most EcoSport lug nuts use a 60-degree conical (acorn) seat to match common wheel patterns.
- Hex size: The socket size needed to tighten/loosen the lug nuts is usually 19 millimeters, though some markets or aftermarket wheels may require a 21-millimeter socket.
In short, while M12 x 1.75 with a 19mm hex is a widely common configuration for many EcoSport variants, you should verify the exact pitch and hex size for your specific vehicle and wheel setup.
How to verify the lug nut size for your EcoSport
To ensure you get the correct lug nuts or replacement wheels, follow these steps.
- Check the owner's manual or the service/maintenance guide for the exact lug nut specification for your year and market.
- Inspect the lug nuts on your current wheel or the wheel information tag (often found on the door jamb or fuel filler area) for the stated size, pitch, and seat type.
- If you’re replacing wheels, bring a sample lug nut or the wheel’s specification sheet to an auto parts store or a Ford dealer to confirm compatibility.
- When in doubt, contact a Ford dealership or a qualified technician with your vehicle’s VIN to pull the exact factory spec.
- Avoid mixing lug nuts with different thread pitches or seat types, which can damage threads and rims.
Proper confirmation helps prevent mismatches that could affect wheel safety and performance.
Yearly/market considerations
EcoSport production spans different markets with varying standards. If your vehicle is from a different region than where you’re doing maintenance (for example, Europe vs. North America), the lug nut size and pitch may differ slightly. Always rely on official documentation or the vehicle’s data plate for the precise specification.
Summary
For many Ford EcoSport models, the practical guide is M12 x 1.75 with a 60-degree conical seat and a 19mm lug nut hex. However, there are regional and year-to-year variations, so verification via the owner’s manual, the vehicle’s data plate, or a Ford dealer is essential before purchasing or replacing lug nuts or wheels. Understanding these details helps ensure safe installation and proper wheel performance across all driving conditions.
What size socket is a 2018 Ford EcoSport lug nut?
12 mm x 1.50 thread size, 13/16" hex.
Can I use 7/8 socket for 22mm?
Yes, you can use a 7/8" socket for a 22mm bolt or nut because they are the same size, with a very small difference that is negligible in practice. 22mm is equal to approximately 0.8660.8660.866 inches, and 7/87 / 87/8 inch is equal to 0.8750.8750.875 inches.
- Size conversion: The two sizes are effectively interchangeable, as they are the closest imperial and metric equivalents.
- Fit: A 7/87 / 87/8" socket will fit on a 22mm bolt. It may feel a little loose, but it will still work.
- Impact tools: This combination is commonly used for impact tools, like those for lug nuts, where sockets are often stamped with both sizes.
- Warning: It's important to use a socket with the correct number of points (e.g., 6-point or 12-point) to avoid damaging the bolt or nut, especially on older or rounded-off fasteners.
What size are the lug nuts on a 2017 Ford EcoSport?
DPAccessories M12x1. 50 Lug Nuts | Closed End Bulge Acorn | 36mm (1.4") Tall | 19mm (3/4") Hex.
What size socket are Ford lug nuts?
The most common socket size for Ford lug nuts is 13/16" or 21mm, especially for models like the F-150 and Bronco. However, sizes can vary by model year and specific vehicle, with some models like the Bronco Sport using a 19mm (or 3/4") socket. It is best to confirm the exact size for your vehicle, as some older or different models might use a different size.
- 13/16" or 21mm: This is the most common size for many modern Ford vehicles, including the F-150 and Bronco. Some sources suggest 13/16" may be a slightly tighter fit than 21mm, which can help prevent rounding the lug nuts.
- 19mm (or 3/4"): This size is used on certain models, such as the Bronco Sport.
- Verification: It's important to check your vehicle's manual or confirm the size before buying tools, especially since some models use a different size or have swollen lug nuts that may require a special socket.
- Swollen lug nuts: If you have a Ford with swollen lug nuts, a standard socket may not fit. In these cases, a special "flip" socket, which has a slightly larger size, can be used to remove them.
