What size is the axle nut on a 2006 Honda Odyssey?
The typical front axle nut size on a 2006 Honda Odyssey is 32 mm hex.
In practice, this size covers most 2006 Odyssey front-wheel-drive models. The exact size can vary by drivetrain configuration or aftermarket parts, so it's important to confirm before replacement. This article explains how to verify and replace the axle nut safely.
Axle Nut Sizing for the 2006 Odyssey
The 2006 Odyssey is primarily front-wheel-drive. The CV axle is secured to the wheel hub with a large hex nut, most commonly a 32 mm size. If you have the rare all-wheel-drive version or a non-stock part, another size could apply. Always verify against official documentation or the parts diagram for your specific VIN.
Why sizes might vary
Differences can occur because of changes in manufacturing or aftermarket parts. The parts diagram for your exact vehicle is the authoritative source to confirm the correct size before you attempt replacement.
To help you verify or replace the nut, here are practical steps:
- Check the official Honda service manual or the parts diagram for your exact VIN/year; the front CV axle nut size is listed there (typically 32 mm for 2006 Odyssey).
- Inspect the existing nut: measure the distance across the flats (the hex) with a caliper if you can't read the size stamped on the nut; attempt fitting a 32 mm socket to see if it engages correctly.
- When ordering parts, use a reputable source and confirm that the nut includes any required lock washer or cotter pin as specified by Honda.
- If replacing, install the nut and torque to the factory specification in the service manual; in most Honda front-axle applications this requires a high torque and proper sequence, and some models require re-torquing after a short break-in period.
- After installation, rotate the wheel by hand to ensure there is no binding and take a short test drive, then recheck torque if the manual calls for retorque after seating the axle.
Concluding: If your measurement differs from 32 mm or you’re unsure, consult a professional mechanic or a Honda dealership parts counter to verify the exact size for your vehicle's VIN and configuration.
Summary
The 2006 Honda Odyssey typically uses a 32 mm front axle nut. Always confirm against your specific VIN and drivetrain configuration in the official service manual or Honda parts diagrams, and replace with a new nut if necessary, tightening to the specified torque and retorquing if required by the manual.
What size is the axle nut on a 2005 Honda Odyssey?
The 2005 Honda Odyssey axle nut has a thread size of M26 x 1.5 and requires a 36mm socket to remove. It's also known as a stake nut and is a front axle nut.
You can watch this video to see how to remove the axle nut on a Honda Odyssey: 56sValley Mobile AutomotiveYouTube · Feb 23, 2023
- Thread size: M26 x 1.5
- Socket size: 36mm
- Position: Front
- Type: Stake nut
What size is the socket on a 2006 Honda Accord axle nut?
36mm
Axle Nut Socket Size: 36mm. Axle Nut Thread Size: M24x1. 5.
What size socket is a Honda axle nut?
The most common Honda axle nut socket sizes are 32mm and 36mm, but the correct size depends on the specific model and year. For 5-speed manual transmissions and some older models, a 32mm socket is often used. Newer models like many Accords, Pilots, and CR-Vs typically use a 36mm socket. To ensure you have the right size, always measure the nut or consult your vehicle's service manual before starting work.
You can watch this video to learn how to remove a Honda axle nut: 1mBundysGarageYouTube · Oct 26, 2017
- 32mm: Commonly used on older Honda models and some 5-speed manual transmissions.
- 36mm: Frequently used on newer models, including many Accords, Pilots, and Ridgelines.
- 34mm: Used on some specific models, such as the Honda CR-V.
This video demonstrates how to remove the axle nut using a 32mm socket: 1mTRQYouTube · Feb 21, 2022
- Always confirm: The best way to be certain is to measure the nut yourself with a caliper or ruler before buying the socket, or check your vehicle's service manual.
- Use the correct socket type: Use a 6-point socket for a better grip and to avoid stripping the nut, especially when loosening it.
What size is the axle nut socket on a 2007 Honda Odyssey?
SPECIFICATIONS
| Position | Front |
|---|---|
| Axle Nut Included | Yes |
| Axle Nut Length | 23 |
| Axle Nut Socket Size | 36 |
| Axle Nut Thread Size | M26×1.5 |
