What size is the oil filter socket on a 2013 Toyota Corolla?
The oil filter socket size for a 2013 Toyota Corolla is 65 mm. This size matches the cap/socket used on the Corolla’s oil filter housing for that year’s 1.8-liter engine configuration.
In this article, we explain the specific size, why it matters for service, and practical steps to change the oil filter on a 2013 Corolla. We also cover tool options and best practices so you can complete the job safely and correctly.
Understanding the oil filter setup on the 2013 Corolla
The 2013 Corolla, powered by the 1.8-liter engine, typically uses a canister-style oil filter with a replaceable cap that requires a dedicated socket/wrench. The standard size for that cap is 65 mm in diameter, which is why many DIYers look for a 65 mm oil filter cap wrench to perform changes cleanly and without damage.
Tools and options for removing the oil filter cap
Use one of these tools to remove or install the 65 mm oil filter cap. If a dedicated cap wrench isn’t available, alternative methods can be used carefully, but they may be less ideal for repeated service.
- 65 mm oil filter cap wrench or socket (preferred)
- Strap wrench or oil filter pliers (for extra grip if needed)
- Rubber gloves, rags, and a drain pan to keep the workspace clean
Having the correct 65 mm cap wrench minimizes the risk of rounding the cap or damaging the housing, and it makes the job faster and cleaner.
Step-by-step: removing and replacing the oil filter on a 2013 Corolla
Below is a practical sequence you can follow. Before starting, verify you have the correct oil type and capacity for your vehicle in the owner's manual.
- Warm up the engine briefly, then park on a level surface and engage the parking brake. Raise the vehicle if needed and support securely with jack stands.
- Place a drain pan under the oil pan, then remove the drain plug and let the old oil drain completely.
- Using the 65 mm cap wrench, loosen and remove the oil filter cap. Remove the old filter cartridge (or spin-on filter, depending on your exact setup).
- Install the new filter cartridge or filter according to the manufacturer’s instructions, and reseat the cap. Torque is not typically specified for the cap itself; snug and hand-tight is usually sufficient, then check for leaks after refilling oil.
- Reinstall the drain plug, then refill the engine with the recommended oil (refer to the owner’s manual for grade and capacity, typically around 4.0–4.4 quarts for the 1.8L engine with filter change). Start the engine, check for leaks, and use the dipstick to confirm proper oil level. Top up if necessary.
Following these steps helps ensure a proper seal, clean operation, and accurate oil level after the change. If you’re unsure about the exact capacity for your vehicle’s market or trim, consult the owner’s manual or a Toyota service bulletin for your VIN.
Tips and caveats for best results
Keep these considerations in mind to avoid common pitfalls during an oil change on the 2013 Corolla.
- Always replace the oil filter gasket or O-ring if your filter design includes one, and ensure the new filter is the correct part for your engine.
- Lubricate the new oil filter seal with a touch of fresh oil to ensure proper seating and easy removal at the next service.
- Do not over-tighten the oil filter cap or drain plug; snug by hand and then a small amount more with a wrench is enough to seal without damage.
- Dispose of used oil and filters according to local regulations; many auto parts stores offer recycling services.
Adhering to these tips helps extend engine life and reduces the risk of leaks or oil loss after a change.
Summary
For a 2013 Toyota Corolla, the oil filter socket size you’ll likely need is 65 mm. This standard size fits the canister-style filter housing used on the 1.8-liter engine, making a dedicated 65 mm cap wrench the most reliable tool for the job. With the right tool and careful steps—draining old oil, removing the cap and filter, installing a new filter, and refilling oil—you can complete a proper oil change efficiently. Always verify exact specifications in the owner’s manual or service bulletin for your market and VIN, and dispose of materials responsibly.
How many mm is a Toyota oil filter?
64.16mm
Toyota Oil Filter Housing Diameter
There is information out there that suggests that there is both a 65mm and 65.5mm housing, referring to the diameter of the 14 point ring on the top. Neither measurement is correct. Both styles of oil filter housing measure 64.16mm.
What kind of oil filter do I need for a 2013 Toyota Corolla?
The 2013 Toyota Corolla oil filter number is 04152-YZZA6 for the Genuine Toyota oil filter. Other filter part numbers that are compatible or replacements include 04152-40060 and 04152-37010, and brands like WIX and Fram offer aftermarket options.
- Genuine Toyota: 04152-YZZA6
- Other compatible Toyota part numbers: 04152-40060 and 04152-37010
- WIX: 57064
- Fram: CH10358
What size is the oil filter wrench on a 2013 Toyota Corolla?
64mm
EWK 64mm 14 Flutes Forged Oil Filter Removal Wrench for 2008-2018 1.8L Toyota Corolla, Prius/Lexus CT200h/ Scion.
What size is the oil filter socket on a Toyota Corolla?
This 64mm 14 flute oil filter wrench for Toyota, Lexus, and Scion vehicles equipped with a 1.8L 4-cylinder engine that uses the newer cartridge style oil filter system.
