What size is the starter bolt on a 2004 Ford f250?
The starter bolt on a 2004 Ford F250 is typically a 3/8-inch bolt. This size is commonly used for the starter motor mounting on this particular truck model.
Detailed Explanation
The 2004 Ford F250 is a heavy-duty pickup truck that was part of the eighth generation of the Ford F-Series lineup. Like other Ford trucks of this era, the starter motor is secured to the engine block using a series of bolts, with the most common size being a 3/8-inch bolt.
The starter motor is responsible for providing the initial rotational force to crank the engine and start the vehicle. It is a critical component that needs to be properly mounted and secured to ensure reliable operation. The 3/8-inch bolt size is a standard specification for this application, as it provides the necessary strength and thread engagement to hold the starter motor in place.
Verifying the Starter Bolt Size
To confirm the starter bolt size on a 2004 Ford F250, you can take the following steps:
- Locate the starter motor, which is typically situated on the lower portion of the engine block.
- Inspect the bolts that secure the starter motor in place. Measure the diameter of the bolts using a caliper or micrometer.
- If the bolts measure approximately 3/8 inches (or 9.5 mm) in diameter, then you have confirmed the correct starter bolt size for your 2004 Ford F250.
It's important to use the correct bolt size when replacing or servicing the starter motor to ensure a secure and reliable connection. Using the wrong size bolt could lead to issues such as the starter motor becoming loose or even falling off, which could potentially cause damage to the engine or other components.
What size bolts are for a 6.0 powerstroke starter?
The top two are smaller of the same size and are 8mm with a 13mm head. The lower one is larger and longer with the length different for a manual trans as opposed to the auto.
What size is the bolt on a Ford starter?
Starter Mounting Bolt, Type 3 Long, 3/8-16 X 1-9/16 In., Ford.
What size socket for 6.0 Powerstroke?
24/36mm
24/36mm Reversible Oil Fuel Filter Socket For 03-10 Ford 6.0 6.4 Powerstroke.
What makes a 7.3 hard to start?
When an ICP is failing, the engine runs extremely rough as load is imposed (under throttle), and the condition can eventually contribute to a 7.3L's inability to start. Oil contamination in the wiring usually is the cause.
What size bolts are on a starter solenoid?
Re: Starter solenoid bolt size? Hi Tom, The electrical hookup bolts will use a standard 1/2" wrench and the bolts that hold the solenoid to the housing will use either a 3/8" wrench OR are long bolts with a standard straight blade screw driver slotted head. Good Luck.
What size Torx bolt is a 6.0 injector?
Install the injector and Torque the hold down bolt to 32.5N.m (24 ft-lb). An under torqued injector hold down bolt will result in failure.
How many bolts does it take to remove a starter?
3 bolts
There are 3 bolts,,, use a 5/8" 12 point socket to remove bolts.
Are all Ford bolts metric?
Are Ford bolts metric or standard? Yes. Ford has sourced both for various vehicle over the years. While it's a general trend that the newest cars are all metric, there are stubborn applications where older “standard” bolts are still used.
What size is the starter bolt on a 7.3 Powerstroke?
W702600S439 OE Starter Bolt, M10 X 35mm, 1995-2003 Ford 7.3L Powerstroke.
What size are starter bolts?
Starter Bolts - Inch & Metric Sizes
| Item Number | Size | Quantity |
|---|---|---|
| 73121 | 3/8" X 1-7/8" | 4 |
| 73122 | 3/8" X 3-5/8" | 4 |
| 73123 | 3/8" X 4-11/16" | 4 |
| 73124 | 3/8" X 4-1/2" | 3 |
