Where is the inertia switch on a 2015 Ford Transit?
The inertia switch on a 2015 Ford Transit is typically located in the rear cargo area on the left-hand side, behind an access panel. In some markets or configurations, it may be mounted under the front passenger kick panel or near the dash. Always check your vehicle’s manual or consult a Ford dealer for the exact location on your VIN.
Fuel-pump safety switches, or inertia switches, are designed to cut power to the fuel pump after a collision or if the vehicle experiences a significant jolt. Because Ford configurations can vary by market and trim level, the switch’s exact placement can differ between regions and model runs. The following guidance covers the common placements and how to verify them on many 2015 Transit vans.
Common locations in the 2015 Transit
Below are locations most often reported by owners and service documentation. If your van’s configuration differs, refer to the official manual or a Ford technician for confirmation.
- Rear cargo area, left-hand side: behind a removable panel or trim along the side wall near the wheel arch.
- Under the front passenger kick panel: some markets place the switch access under the dash on the passenger side.
- In rare cases or certain trims, access may be gained through an adjacent panel in the cargo area or near the bumper area; always verify with the manual.
If you cannot locate the switch after checking these areas, consult the owner’s manual specific to your vehicle’s VIN or contact a Ford dealership for guidance tailored to your build date and region.
Resetting the inertia switch
Resetting the inertia switch is a straightforward procedure when the switch has been triggered. Before you begin, ensure there has been no recent collision or obvious damage and that it is safe to work on the vehicle.
- Turn the ignition off and remove the key; ensure the vehicle is in a safe, parked position.
- Locate the red reset button on the inertia switch (the exact location depends on your vehicle’s configuration, see the locations above).
- Press and firmly release the red button to reset the switch. You should feel or hear a click indicating it has reset.
- Turn the ignition to the ON position and listen for the fuel pump priming (a brief hum). Wait a few seconds, then try to start the engine.
If the vehicle still won’t start, or the switch trips again shortly after resetting, do not drive the van. A fault in the fuel system or related wiring may be present, and a Ford-certified technician should diagnose and repair the issue.
Notes for owners and operators
Given regional variations in the Transit’s design, always start with the owner’s manual for your exact year and market. If you’re unsure, contact a Ford dealer or an authorized service center to confirm the precise inertia switch location and proper reset procedure for your VIN.
Summary
For a 2015 Ford Transit, the inertia switch is most commonly found in the rear left cargo area behind a trim panel, with some configurations placing it under the front passenger kick panel. Access and reset procedures are straightforward but can vary by market and trim. When in doubt, consult the vehicle’s manual or a Ford service professional to confirm the location and safe reset steps. A correctly reset inertia switch restores power to the fuel pump, but any repeated trips or starting failures warrant professional inspection to rule out underlying fuel or electrical faults.
Where is the fuel cut off switch on a 2014 Ford Transit?
Once the vehicle determines the systems are safe, then the vehicle allows you to restart. The fuel pump shut-off switch is located behind an access panel on the right side of the luggage compartment.
Where is the inertia switch located?
The location of an inertia switch varies by vehicle, but it is commonly found on the passenger side, either behind the kick panel, under the dash in the footwell, or near the center console. For some models, it may be in the trunk or near the fuel tank on the driver's side. You can often find it by looking for a plastic panel near the front passenger door or by checking for a small switch with a red button on top.
This video shows the common locations of an inertia switch in Ford vehicles: 59sJunk works GarageYouTube · Sep 14, 2017
Common locations
- Passenger-side kick panel: This is a common spot, often requiring you to remove a small plastic access panel to get to the switch.
- Passenger-side footwell: The switch may be located on the floor, sometimes against the firewall, in the area where a passenger's feet would be.
- Behind the dashboard: Some vehicles have the switch located behind the dashboard, which might require you to pull back the carpet or remove other trim to access.
- In the trunk: On some Ford SUVs, the inertia switch is located in the trunk on the driver's side, behind a small compartment.
How to identify and reset
- Look for the red button: The inertia switch is almost always identifiable by a red button on its top. The button will be in a raised position if the switch is tripped.
- Ensure no fuel leaks: Before attempting to reset, make sure there are no fuel leaks around the vehicle.
- Press to reset: Push the red button down firmly to reset the switch. You should hear a click when it is reset.
- Check for a cover: The switch may be hidden behind a small panel, cover, or piece of plastic that needs to be removed first.
Do Fords still have inertia switches?
Like it or hate it, the Ford/Lincoln Inertia switch was still a great safety feature. But why then would Ford/Lincoln stop using them? The simple answer is, they haven't. Granted modern Ford/Lincoln vehicles do not still use the switch with the red button, however they still utilize a fuel pump shutoff feature.
Where is the inertia switch on a 2015 Ford Transit Connect?
The fuel shutoff inertia switch in the 2015 Ford Transit Connect is located behind the glove box on the passenger side. If the vehicle cranks but won't start, check this switch—it trips during impacts to cut fuel flow.
