Why are the power windows not working on my Ford Explorer Sport Trac?
If the power windows in your Ford Explorer Sport Trac are not functioning, there could be a few potential causes. The most common issues include a blown fuse, a faulty window motor, or a problem with the window switch. Let's explore these potential problems and how to troubleshoot them.
Checking the Fuse
The first step is to check the fuse for the power windows. The fuse box is typically located in the engine compartment or under the dashboard. Locate the fuse for the power windows and inspect it to see if it has blown. If the fuse is blown, replace it with a new one of the same amperage rating. If the new fuse also blows, there may be an underlying electrical issue that needs to be addressed.
Inspecting the Window Motor
If the fuse is not the issue, the problem may be with the window motor itself. The window motor is responsible for raising and lowering the window. Over time, the motor can wear out or become damaged, preventing the window from moving. To test the motor, you can try manually operating the window. If the window moves with manual operation but not with the power switch, the motor is likely faulty and will need to be replaced.
Troubleshooting the Window Switch
Another potential cause of non-functioning power windows is a problem with the window switch. The switch sends an electrical signal to the window motor, telling it to move the window up or down. If the switch is malfunctioning, it may not be sending the correct signal to the motor. You can test the switch by using a multimeter to check for continuity when the switch is pressed.
Seeking Professional Assistance
If you've checked the fuse, the window motor, and the window switch, and the problem persists, it's best to have a professional mechanic diagnose and repair the issue. They can use specialized tools and equipment to identify the root cause of the problem and make the necessary repairs.
In summary, the most common reasons for power windows not working on a Ford Explorer Sport Trac are a blown fuse, a faulty window motor, or a malfunctioning window switch. By following these troubleshooting steps, you can identify the problem and take the appropriate action to restore your power windows to full functionality.
How to reset Ford power window?
To reset a Ford power window, roll the window all the way down and hold the switch for a few seconds. Then, roll the window all the way up and hold the switch again for a few seconds to complete the reset. This process recalibrates the window's limits and often fixes the "one-touch" or anti-pinch functions.
This video demonstrates how to reset Ford power windows: 38sDIY PintoYouTube · Apr 22, 2024
Step-by-step reset procedure
- Turn the ignition to the "run" position.
- Lower the window completely by pulling and holding the switch down. Release the switch once the window is fully down.
- Continue holding the switch in the down position for a few seconds after the window stops moving.
- Now, raise the window completely by lifting and holding the switch up. Release the switch when it is fully closed.
- Keep the switch in the up position for a few seconds after the window is closed.
- Repeat for any other windows that need to be reset.
Why this is necessary
- Battery issues: This reset is often needed after the vehicle's battery has been disconnected or gone flat.
- "Bounce-back" feature: It can fix the issue where the window automatically closes, then reopens halfway, a safety feature that can sometimes be triggered incorrectly.
- One-touch function: This procedure restores the "one-touch" up and down functions that may have stopped working.
Why would all four power windows stop working?
If all four power windows stop working, first check the main fuse and the power window relay in the fuse box. Inspect the master window switch on the driver's door for corrosion or damage. Test for voltage at the window motors using a multimeter. Faulty wiring or a bad ground connection can also cause failure.
What to do if power windows stopped working?
Step-by-Step Guide to Troubleshooting Power Window Problems
- Step 1: Check the Fuse. The first step in troubleshooting any electrical issue in your car is checking the fuse.
- Step 2: Inspect the Window Switch.
- Step 3: Test the Window Motor.
- Step 4: Check the Regulator and Tracks.
- Step 5: Examine the Wiring.
Why are the windows not working on my Ford Explorer?
If the driver's power window stops working, first check the window fuse and switch for power. Remove the door panel to inspect the window motor and regulator assembly. Common causes include worn motor brushes or broken regulator cables. Test the motor with a multimeter and replace if faulty.
