How do I put my Chevy in TPMS relearn mode?
On most Chevrolet models, you can start TPMS relearn from the vehicle’s TPMS menu inside the Driver Information Center (DIC) or by using a dash-mounted reset button, then you complete the process by driving at highway speeds. The exact steps depend on your model year and trim, so check your owner’s manual if you’re unsure.
Understanding TPMS relearn in Chevy vehicles
TPMS relearn is needed after rotating tires, replacing sensors, or adjusting tire pressures. If the system can’t auto-learn after a reset or tire change, you’ll need to initiate relearn manually. The most reliable approach is to follow the path in your vehicle’s TPMS menu, but some older or specific trims still use a physical reset button.
Using the Driver Information Center (DIC) TPMS relearn procedure
This method covers most recent Chevrolet cars and trucks. It uses the built‑in TPMS menu accessed via the steering wheel controls and gauge cluster.
- Check that all tires are inflated to the recommended pressures listed on the door placard, including the spare if your vehicle uses it for TPMS focus.
- Turn the ignition to ON with the engine off (or press the Start button once to RUN, without pressing the brake).
- On the steering wheel, navigate to the Vehicle Information Menu or Tire Pressure Monitor (TPMS) screen until you see an option labeled TPMS Relearn, Tire Pressure Monitor, or Relearn Sensor.
- Select the Relearn option and confirm to start the relearn process. The dash indicator may flash or a message will appear indicating that relearn is in progress.
- Drive the vehicle at a steady speed—typically 50 mph (80 km/h) or higher—for about 10 minutes, or until you receive a confirmation that the relearn is complete.
After completing these steps, the system should confirm that the TPMS relearn is finished. If you don’t see a confirmation, or if the tire pressure warning light remains on, repeat the steps or proceed to the troubleshooting notes below.
Manual reset button or dash sequence (for models with a physical reset)
Some Chevy trims retain a physical TPMS reset button or a quick dash sequence as an alternative relearn method. This can be located under the dash to the left, near the hood latch, in the glove box, or in the center console area. The exact location varies by model and year, so refer to your manual or a dealership if you’re unsure.
- Ensure all tires are inflated to the recommended pressures.
- Turn the ignition to ON with the engine off (or press START to RUN, without starting the engine).
- Press and hold the TPMS reset button (or perform the dash sequence as described in your owner’s manual) until the TPMS light begins to blink slowly, then rapidly, or until a chime/confirmation occurs.
- Release the button and wait for the confirmation message or light pattern. Drive to complete the relearn; speeds and duration are typically similar to the DIC method (about 10 minutes at 50 mph+).
Not all Chevy models support a physical reset, so if you can’t locate a TPMS button or the dash sequence doesn’t respond, use the DIC method or a professional tool.
Using a professional tool or service if the relearn doesn’t work
If the relearn still won’t complete after trying the DIC or button methods, you may need to use an automotive scan tool or visit a tire shop or dealership. A tool can communicate with each TPMS sensor (including any new sensors) to program or relearn them individually, especially if a sensor was replaced or a tire was rotated long ago.
- Ensure all tires are inflated correctly.
- Use a TPMS relearn tool or have a professional perform a sensor-by-sensor relearn with the vehicle on and the ignition in RUN.
- Follow the tool’s prompts or the technician’s instructions to complete the relearn. Finalize by driving at highway speeds as indicated by the tool or manual.
Professional relearn is especially helpful after replacing a sensor, mounting a new tire, or if a vehicle has multiple tire changes across a short period.
Troubleshooting and tips
If your TPMS light stays on after attempting relearn, consider these quick checks:
- Double-check tire pressures and re-inflate if needed.
- Make sure you are following the exact steps for your model year; some details differ between trims.
- Inspect sensors for damage or corrosion; a faulty sensor will prevent relearn.
- If a wheel was replaced, ensure the sensor is seated correctly and that the valve stem is not leaking.
If problems persist, contact a Chevrolet service center or tire shop for a diagnostic relearn using a professional tool.
Summary
Putting your Chevy into TPMS relearn mode typically involves either using the Driver Information Center TPMS menu or a dash-mounted reset method, followed by driving at a steady highway speed for about 10 minutes. The exact steps vary by model year and trim, so always consult your owner’s manual for model-specific instructions. If the relearn doesn’t succeed, a professional scan tool or dealership visit can complete sensor programming and ensure accurate tire pressure monitoring.
