How do you reset the tire pressure sensor on a Chevy Cobalt?

In most Chevy Cobalt models, resetting the tire pressure monitoring system starts with inflating all tires to the recommended pressures and then allowing the system to relearn through normal driving. Depending on the year and trim, you may also need to perform a dedicated TPMS Learn procedure using a button or a diagnostic tool. Here’s how to approach the process and what to watch for.

Two common ways to reset TPMS on the Cobalt

The following methods cover the two most frequently encountered approaches. One relies on a simple drive-after-inflation relearn, while the other uses a dedicated Learn procedure if your car is equipped with a TPMS Learn button or requires a scan-tool relearn.

1. Check and inflate all tires to the vehicle’s recommended cold tire pressures, including the spare if applicable, as listed on the door jamb placard or in the owner’s manual.


2. With the tires inflated properly, drive on a level road at steady speeds above about 50 mph (80 km/h) for 10 to 15 minutes to allow the system to relearn the new pressures. If using indirect TPMS, this may happen automatically after a period of normal driving.


3. If the warning light remains after the drive, recheck tire pressures for accuracy and inspect for slow leaks, then repeat the highway drive. If the light still stays on, the sensor batteries or sensors may be failing and professional service may be required.

In some model years, Chevy provided a dedicated TPMS Learn procedure that uses a button or a scan tool to initiate learning. If your Cobalt has this feature, follow these steps.

TPMS Learn button or tool-based relearn

Note: Not all Cobalt models include a Learn button. If your vehicle has one, it is typically located on the left side of the dash, near the steering column or under the driver’s side dash panel. If in doubt, consult the owner’s manual or a dealership tool.

1. Turn the ignition to the ON position with the engine off, and ensure tires are at their recommended cold pressures.


2. Press and hold the TPMS Learn button until the TPMS indicator confirms learning (commonly seen as a brief flash or a chime). Some vehicles may require a scan tool to initiate the process.


3. Drive the car at a steady speed (around highway speeds) for 10 minutes to complete the relearn. The warning light should go out once the sensors are learned.

If you suspect a faulty sensor, battery, or failed TPMS module, or if you have recently installed new tires, you should have the system checked by a tire shop or dealer. They can use a diagnostic tool to verify sensor IDs and reset the system accurately.

Summary

Resetting the Chevy Cobalt’s TPMS typically begins with proper tire inflation and a highway-speed drive to trigger automatic relearning. If your model has a TPMS Learn button or requires a scan tool, follow the owner’s manual guidance or visit a professional for a precise reset. Maintaining correct tire pressures helps keep the system accurate and reliable.

How to clear a tire pressure sensor light?

To reset the TPMS light, first ensure all tires are properly inflated and then use the reset button on your dashboard or the vehicle's infotainment system to begin the recalibration process. If your vehicle lacks a reset button, you can try driving for a short period at a higher speed (around 50 mph) to trigger an automatic reset. If the light persists after these steps, the problem could be a faulty sensor, and you may need professional inspection.
 
Method 1: Use the TPMS reset button 
This video demonstrates how to reset TPMS light using the TPMS reset button: 59sApple DrainsYouTube · Oct 5, 2012

1. Inflate all tires to the correct pressure. 
2. Turn the ignition to the "On" position without starting the engine. 
3. Press and hold the TPMS reset button until the tire pressure light blinks three times. The button is often located under the steering wheel. 
4. Release the button and start the vehicle. 
5. Wait for at least 20 minutes for the system to recalibrate. 

Method 2: Automatic recalibration

1. Inflate all tires to the correct pressure. 
2. Drive the vehicle for about 10–20 minutes at a speed of 12–15 mph or higher, as recommended by some manufacturers like Hyundai. 
3. Other vehicles may require driving at or above 50 mph for at least 10 minutes. 

Method 3: Use the infotainment system (if available) 

1. Ensure the ignition is "On" and the transmission is in Park.
2. Navigate to the vehicle settings menu on your infotainment screen.
3. Find the "TPMS Calibration" or similar option.
4. Follow the on-screen instructions to calibrate the system, which may require driving for a period of time. 

If the light remains on

• Double-check the tire pressure: Re-verify that all tires are inflated to the correct PSI, including the spare if it has a sensor. 
• Inspect for leaks: Look for any nails or other damage to the tires. 
• Check for sensor issues: The light may stay on if a sensor is faulty. 
• Take it to a professional: If you cannot reset the light, it's best to have a professional check the system for you. 

How to reset TPMS on Chevy Cobalt?

The tire pressure monitoring sensors in the wheels. Simply get the key in turn it till it's in the on position without started you got all your lights. Going. And you take your info.

How do you reset the tire pressure sensor on a 2010 Chevy Cobalt?

With the vehicle off, turn the key to the "On" position, but don't start the car. Hold the TPMS reset button until the tire pressure light blinks three times, then release it. Start the car and wait 20 minutes for the sensor to refresh.

Where is the reset button on the Chevy tire pressure sensor?

The TPMS reset button on a Chevy is often located under the steering wheel, but the procedure can also involve using the vehicle's driver information center (DIC) or a separate tool. For many models, there isn't a simple button to press; instead, you'll need to navigate the menu in the instrument cluster and follow the "relearn tire positions" prompts to reset the system, often with a special tool to activate each sensor. If you can't find it, consult your owner's manual.
 
This video shows how to reset the tire pressure monitoring system on a 2007-2013 Chevy Silverado: 1m1A Auto: Repair Tips & Secrets Only Mechanics KnowYouTube · Feb 15, 2019
Common reset procedures

• Using the driver information center (DIC): This is the most common method for newer models. 
  1. Turn the ignition to the "On" position (without starting the engine). 
  2. Use the vehicle's buttons or steering wheel controls to navigate the DIC until you find the "Tire Pressure" or "Vehicle Settings" menu. 
  3. Select "Relearn Tire Positions" or "TPMS Calibration". 
  4. Press and hold the appropriate button (like the "Check" button or trip-reset stalk) to activate the relearn mode. 
  5. The vehicle will prompt you to start the process. You will then need to use a TPMS activation tool to trigger each sensor, starting with the driver's front tire, until you hear a horn chirp. 
• Using a physical button (older models): Some older models have a physical button.
  1. Turn the ignition to the "On" position. 
  2. Locate the TPMS reset button, typically under the steering column. 
  3. Press and hold the button until the tire pressure light flashes three times. 
• Using tire pressure adjustments: In some cases, simply over-inflating the tires and then deflating them can reset the system. 
  1. Inflate each tire to 3 PSI above the recommended level. 
  2. Completely deflate each tire, including the spare if it has a sensor. 
  3. Inflate all tires to the correct pressure. 
• Using the key fob (some models): On some models with keyless entry, you can use the remote to activate the relearn mode. 
  1. Park the vehicle and turn the ignition to the "On" position. 
  2. Press and hold the "LOCK" and "UNLOCK" buttons on the key fob simultaneously for about five seconds. 
  3. Follow the on-screen prompts or use a TPMS activation tool on each tire as described above. 
• Using the battery (last resort): If all else fails, you can try disconnecting the battery.
  1. Disconnect the negative battery cable. 
  2. Turn the key to the "On" position and honk the horn for a few seconds to discharge any residual power. 
  3. Reconnect the battery. 

This video shows how to reset the tire pressure monitoring system on a 2014 Chevy Silverado: 53sBartec TPMSYouTube · Aug 13, 2014
Important considerations

• Before attempting a reset, always check your tires for punctures and ensure they have the correct air pressure, as low pressure is the most common cause of the TPMS light being on. 
• Your vehicle's owner's manual will have the most accurate information for your specific make and model. 
• If the light remains on after attempting a reset, there may be a problem with a sensor itself.