How do you reset the tire pressure sensor on a Toyota Corolla?

To reset the TPMS on a Toyota Corolla, you typically inflate all tires to the recommended pressures and perform either a direct reset using a button (if your model has one) or allow the system to relearn automatically by driving at highway speeds. The exact method depends on the model year and trim level.

Two common TPMS reset approaches for the Corolla

The following methods cover the two most widely used reset paths. One relies on a dedicated TPMS reset button (where equipped); the other relies on automatic relearn through driving after correcting tire pressures.

Method A: TPMS reset button (where equipped)

Use this method if your Corolla has a TPMS reset or SET button located on the dashboard area. Not all trims include this button, so if you don’t see one, skip to the driving relearn method.

1. Inflate all tires to the recommended cold pressures found on the driver’s door jamb sticker or in the owner’s manual.


2. Turn the ignition to ON, with the engine off.


3. Locate the TPMS reset button (often labeled SET or TPMS) on the lower left side of the dash or near the steering column.


4. Press and hold the button until the TPMS indicator light begins to blink or beep, then release. The exact pattern can vary by model year.


5. Start the engine and drive straight for at least 10 minutes at speeds above about 50 mph (80 km/h) to complete the relearn.


6. Watch the TPMS light: if it goes out, the reset was successful; if it stays on, recheck tire pressures and consider professional inspection if needed.

The button-based reset gives you a direct initiation of the relearn process. If your model doesn’t have this button, or the light remains after following these steps, proceed with the driving-based method below.

Method B: Sensor relearn by driving (no reset button)

Many newer Corolla models rely on automatic relearn through normal driving after you’ve brought all tires to the correct pressures. This method is common when a dedicated reset button isn’t present.

1. Inflate all tires to the recommended cold pressures (including the spare, if your system requires it for relearn).


2. With the engine running, drive on a highway or freeway at steady speeds above 50 mph (80 km/h) for 10–20 minutes to trigger the relearn process.


3. Occasionally, the TPMS light may flash during learning and then settle to off; if it remains on after a sufficient drive, recheck pressures and look for leaks or sensor issues.

Automatic relearn relies on the system recognizing sensor signals as you drive. If the light persists after a thorough highway drive, it’s a sign to inspect tires for leaks, damaged sensors, or a possible fault in the TPMS.

What to do if the TPMS light stays on

If the TPMS warning remains illuminated after attempting either reset method, take these steps: recheck every tire’s pressure with a reliable gauge, look for obvious punctures or slow leaks, verify that the tires are cold before measuring, and inspect the valve stems and seals. If pressures are correct and the light won’t reset, or you hear a hissing sound or suspect a damaged sensor, schedule service with a dealership or qualified tire shop to diagnose potential sensor or wheel issues.

Notes on model-year differences

The exact reset procedure can vary by Corolla generation and trim. Some newer models rely strictly on automatic relearn with no reset button, while older trims offer a manual reset option. If you’re unsure which method applies to your car, consult the owner’s manual or contact a Toyota service center for model-specific instructions.

Summary

Resetting the TPMS on a Toyota Corolla generally starts with inflating all tires to the recommended pressures. If your model has a TPMS reset button, use it as directed and then drive at highway speeds to complete the relearn. If there’s no reset button, rely on a driving-based relearn by maintaining higher speeds for 10–20 minutes. If the warning light persists, have tire pressures checked again and seek professional service to inspect sensors or potential leaks. Keeping tires properly inflated helps ensure accurate readings and safer driving.

How to reset low tire pressure light on 2010 Toyota Corolla?

To reset the 2010 Toyota Corolla's low tire pressure light, first inflate all tires to the correct pressure. Then, turn the ignition to the "On" position (without starting the engine), press and hold the TPMS reset button (located on the dashboard near the steering wheel) until the light flashes three times, and release the button. Wait a few minutes for the system to register the new pressures before driving.
 
This video shows how to locate and use the TPMS reset button on a Toyota Corolla: 56sSimon Says GarageYouTube · Apr 15, 2024
Step-by-step reset instructions

• Inflate your tires: Check your vehicle's recommended tire pressure and inflate all four tires accordingly. 
• Turn the ignition on: Insert the key into the ignition and turn it to the "On" position, but do not start the engine. 
• Locate the TPMS reset button: Find the TPMS reset button, which is usually a small, round button with a tire symbol on it, located on the dashboard to the right of the steering wheel or under the steering column. 
• Press and hold the button: Press and hold the reset button until the tire pressure warning light on the instrument panel blinks slowly three times. 
• Release the button: Release the button after the light blinks three times. 
• Wait for the system to initialize: With the engine still running, wait for several minutes to allow the system to read the new tire pressures. The light should then turn off. 

This video demonstrates the entire process of resetting the TPMS light, including inflating the tires: 56sToyota MaintenanceYouTube · Aug 25, 2014
What to do if the light stays on

• If the light continues to flash continuously after you've reset it, there is a system malfunction, likely a bad sensor. In this case, it's best to take your car to a tire shop or a dealer for a professional diagnosis and repair. 
• If the light comes on after a few minutes and then stays on, the system is correctly indicating a problem and a manual reset won't fix it. 

You can watch this video to understand why the TPMS light might keep flashing: 56sToyota MaintenanceYouTube · Feb 17, 2022

How do you reset the low tire pressure light on a 2013 Toyota Corolla?

To reset the 2013 Toyota Corolla TPMS, first ensure all tires are properly inflated. Then, turn the key to the "ON" position (without starting the engine) and find the TPMS reset button, usually located under the steering wheel. Press and hold the button until the TPMS light flashes three times, then release it. Start the car, and the system should reset itself within about 20 minutes. 
This video demonstrates how to reset the TPMS light on a Toyota Corolla: 56sToyota MaintenanceYouTube · Aug 25, 2014
Step-by-step reset guide

1. Inflate tires: Park the car and adjust the pressure in all tires to the manufacturer's recommended cold tire inflation pressure. 
2. Locate the reset button: Find the TPMS reset button, which is typically a small, round button with a tire icon, located on the dashboard below the steering wheel. Some models may have a different procedure. 
3. Turn the ignition: Insert the key and turn it to the "ON" position, but do not start the engine. 
4. Press and hold the reset button: Press and hold the TPMS reset button until you see the tire pressure warning light on the instrument cluster flash slowly three times. 
5. Release the button: Release the button after the light flashes three times. 
6. Start the engine: Start the engine and drive. The TPMS light should turn off automatically once the system has refreshed, which may take up to 20 minutes. 

If the light remains on
If the light continues to flash after the reset procedure, it could indicate a different issue, such as a sensor fault or a low battery in one of the sensors. In this case, it is recommended to have a professional diagnostic check performed to identify and fix the specific problem.

Where is the tire pressure sensor reset button located?

The Tire Pressure Monitoring System (TPMS) reset button, if your vehicle has one, is most often located under the steering wheel. However, the exact location varies by make and model and can be on the dashboard, in the glove box, or on the center console. Some vehicles may not have a physical button and use the vehicle's information display or menu system to calibrate the tires instead. If you cannot find the button, you should consult your owner's manual or check the driver's information center through the touchscreen.
 
This video demonstrates how to reset the tire pressure warning light on a vehicle with a display audio system: 14sHondaYouTube · May 15, 2019
Common locations

• Under the steering wheel: This is the most frequent location, often to the left of the steering column. 
• On the dashboard: It may be on the driver's side of the dashboard. 
• In the glove box: Some vehicles have the button inside the glove box. 
• On the center console or handbrake: In some cases, it can be found on the center console or near the handbrake. 

If you can't find a button

• Use the vehicle's menu system: Many modern cars have a TPMS calibration option in the settings menu on the dashboard's display screen. 
• Consult the owner's manual: The manual will provide the exact procedure and button location for your specific vehicle. 
• Drive your car: Some vehicles automatically reset the sensors after driving for a period of time, often above 505050 mph for at least 10 minutes. 

Where is the TPMS reset button on a Toyota Corolla?

The TPMS reset button on a Toyota Corolla is typically located either in the glove compartment or on the dashboard, to the left of the steering wheel. If your Corolla has a display screen on the dashboard, there may not be a physical button; instead, you'll use the buttons on the steering wheel to navigate through the menus to find the "Vehicle Settings" and "TPWS" (Tire Pressure Warning System) options to reset the system.
 
This video shows the location of the TPMS reset button in the glove compartment of a 2017 Toyota Corolla: 45sLehewYouTube · Feb 12, 2018
For models with a physical button

1. Locate the button: The button is usually in the glove box or on the instrument panel below the steering wheel to the left. It will have a TPMS icon on it. 
2. Ensure correct tire pressure: Before resetting, make sure all tires are inflated to the correct pressure specified on the driver's side door jamb sticker. 
3. Turn the ignition on: With the engine off, turn the key to the "On" position (or press the start button without starting the engine). 
4. Press and hold the button: Press and hold the TPMS button until the TPMS indicator light on the instrument panel blinks three times. 
5. Release and wait: Release the button after the light blinks three times. Drive the vehicle for a few minutes for the system to recalibrate. 

You can watch this video to see how to reset the TPMS using the physical button: 56sToyota MaintenanceYouTube · Aug 25, 2014
For models with a steering wheel button and display

1. Ensure correct tire pressure: Make sure all tires are inflated to the correct pressure. 
2. Turn the ignition on: Turn the key to the "On" position without starting the engine. 
3. Navigate the menu: Use the steering wheel buttons to navigate to the "Settings" menu on the information display, then find "Vehicle Settings". 
4. Find the TPWS option: Navigate to the "TPWS" or "Tire Pressure Warning System" setting and select "Set Pressure" or "Calibrate". 
5. Confirm the reset: Follow the prompts, which may involve pressing and holding the "OK" button until the light blinks three times, indicating the reset is complete. 

This video demonstrates how to reset the TPMS using the steering wheel buttons: 55sAuto Smart RepairYouTube · Sep 28, 2023