How do you reset the TPMS on a Dodge Challenger?

To reset the Tire Pressure Monitoring System (TPMS) on a Dodge Challenger, you'll need to follow a few simple steps. The TPMS is designed to alert you when the tire pressure in one or more of your vehicle's tires drops below the recommended level, and resetting it is important to ensure the system is functioning properly.

Steps to Reset the TPMS on a Dodge Challenger

1. Ensure all tires are inflated to the recommended pressure level, which can be found in your owner's manual or on the driver's side door jamb sticker.


2. Turn the ignition to the "On" position, but do not start the engine.


3. Locate the TPMS reset button, which is usually found near the steering wheel or in the center console.


4. Press and hold the TPMS reset button for approximately 5 seconds, or until the TPMS warning light on the dashboard begins to flash.


5. Start the engine and let the vehicle run for a few minutes to allow the TPMS to complete the reset process.


6. Once the TPMS warning light stops flashing and remains solid, the reset is complete.

It's important to note that the TPMS reset process may vary slightly depending on the model year and trim level of your Dodge Challenger. If you're unsure of the specific steps, refer to your owner's manual or consult with a Dodge dealer or certified mechanic.

Why Reset the TPMS on a Dodge Challenger?

Resetting the TPMS on your Dodge Challenger is important for several reasons:

• Tire Pressure Monitoring: The TPMS is designed to monitor the air pressure in your vehicle's tires and alert you when the pressure drops below the recommended level. Resetting the system ensures it's functioning correctly and providing accurate readings.


• Fuel Efficiency: Properly inflated tires can improve your Challenger's fuel efficiency, which can save you money on gas and reduce your environmental impact.


• Tire Wear: Underinflated tires can wear more quickly, leading to the need for premature tire replacement. Resetting the TPMS helps you maintain the proper tire pressure and extend the life of your tires.


• Safety: Properly inflated tires provide better traction, handling, and braking performance, which can enhance the overall safety of your Dodge Challenger.

By following the steps outlined above, you can easily reset the TPMS on your Dodge Challenger and ensure your vehicle's tires are properly inflated and functioning as intended.

Where is my TPMS reset button located?

Process will begin if there's no button the procedure is done with the display audio. Begin by pressing the home. Button then touch settings touch vehicle next and then TPMS calibration.

How do you reset the TPMS on a Dodge?

To reset the TPMS on a Dodge, first inflate tires to the recommended pressure, then either wait for the system to auto-reset after driving above 15 mph for up to 20 minutes, or use the dashboard button or on-screen menu to manually calibrate. If the light stays on or flashes, a faulty sensor or other issue may need professional service.
 
This video demonstrates how to reset the TPMS on a Dodge Charger: 1mAuto Repair GuysYouTube · Dec 25, 2016
Manual reset with a button or screen 
For models with a TPMS reset button

1. Ensure all tires are inflated to the correct pressure. 
2. Turn the ignition to the "On" position (without starting the engine). 
3. Press and hold the TPMS button, which is usually located below the steering wheel, until the tire pressure light blinks twice. 
4. Start the vehicle and drive at speeds between 30 and 60 mph for about 30 minutes to allow the system to complete the calibration. 

This video shows how to reset the TPMS on a Ram 1500 using the dashboard button: 53sToolBox TipzYouTube · Jun 4, 2025
For models with a display audio system

1. Press the "Home" button, then select "Settings," then "Vehicle," and then "TPMS Calibration".
2. Select "Calibrate" and the system will begin recalibrating.
3. Drive for about 30 minutes at speeds between 30 and 60 mph to complete the process. 

Automatic reset

• After inflating your tires to the correct pressure, the system will often reset itself automatically after a short period of driving.
• You may need to drive for up to 20 minutes at speeds over 15 mph before the warning light turns off. 

When to see a professional

• If the warning light flashes on and off at startup, it indicates a system malfunction, possibly a faulty sensor or sensor battery. 
• If the light remains on after inflating the tires and trying to reset the system, have a technician inspect the sensors and system for any issues. 

How to reset tire pressure light on 2014 Dodge Challenger?

To reset the tire pressure light on a 2014 Dodge Challenger, first, inflate all tires to the correct pressure listed on the driver's doorjamb. If the light doesn't turn off, you can trigger the reset by using a physical button (if your model has one) located near the steering column by turning the key to "On" and holding the button until the light blinks, then wait for the system to refresh, or by driving the vehicle at speeds over 15 mph for about 20 minutes, which should allow the system to auto-relearn. 
This video demonstrates how to reset the TPMS light on a Dodge Challenger with a physical button: 1mHondaYouTube · May 15, 2019
Option 1: Use the TPMS reset button (if equipped) 

1. Make sure all tires are properly inflated. 
2. Turn the ignition key to the "On" position, but do not start the engine. 
3. Locate the TPMS reset button, which is usually near the steering column and has a TPMS icon. 
4. Press and hold the button until the tire pressure light in the instrument panel blinks twice. 
5. Start the car and wait for the system to refresh. The light should turn off after the system recalibrates. 

Option 2: Use the auto-relearn procedure 

1. Inflate all tires to the correct pressure, found on the sticker in the driver's door jamb. 
2. After inflating, drive the vehicle for approximately 20 minutes at speeds of 15 mph or higher. 
3. The system should automatically detect the new pressures and the light will turn off. 

This video explains the auto-relearn procedure for the TPMS system, which is useful for resetting the light after inflating tires: 47sDigital Glove BoxYouTube · May 27, 2025
Other methods if the light remains on

• Try inflating tires slightly higher: Inflate all tires 3-5 PSI above the recommended pressure, drive for a while until the light goes off, then release air to reach the correct pressure. 
• Check the fuse: The TPMS fuse is located in the trunk under the carpet liner. It may be labeled as fuse #22 or #F25, depending on the model year, and needs to be checked for a burnt-out element. 
• Disconnect the battery: As a last resort, turn the vehicle off, disconnect the positive battery cable, turn the car on and honk the horn for about three seconds to discharge any residual power, then reconnect the battery. 

Where is the TPMS reset button on a Dodge Challenger?

The TPMS reset button on a Dodge Challenger is located to the left of the steering column, near the steering wheel, or sometimes hidden under the dashboard. If your model has a touchscreen display, the reset is done through the "Settings" > "Vehicle" > "TPMS Calibration" menu instead. After calibrating, the system may need to be driven for a while to fully reset. 
This video demonstrates how to reset the TPMS using the steering column button on a Dodge Challenger: 1mHondaYouTube · May 15, 2019
If you have a physical button:

• Locate the button: Look for a button labeled with the TPMS icon to the left of the steering column or under the dashboard.
• Turn the ignition on: With the car in park and the parking brake set, turn the key to the "On" position but do not start the engine.
• Press and hold: Push and hold the button until the TPMS indicator light in the instrument cluster blinks twice.
• Release the button: Let go of the button after the light blinks. 

If you have a touchscreen display:

• Navigate the menu: On the home screen, touch "Settings," then "Vehicle," and then "TPMS Calibration".
• Start the process: Select "Calibrate" to begin the process. 

After resetting:

• Drive the vehicle: The system takes time to recalibrate. You may need to drive for up to 30 minutes at speeds between 30-60 mph for the process to complete. 

If you can't find the button:

• Check the owner's manual for your specific model year. 
• Look in the glove compartment or other areas under the dashboard. 

This video shows the location of the TPMS fuse in a Dodge Challenger, which is a different system than the physical reset button: 1mElectrical Car Repair LIVEYouTube · Sep 12, 2022