How many quarts of oil go in a 2017 Chevy Spark?
Typically about 4 quarts of engine oil are needed for a standard oil change on a 2017 Chevy Spark, including a new filter. In practice, most owners end up with roughly 3.7 to 4.0 quarts on the dipstick after filling and checking.
In this article, we explore the expected oil capacity for the Spark, how engine variants can influence the amount, the recommended oil type, and steps to verify the level. We also offer practical tips for performing a change correctly.
Oil capacity by engine configuration
The Spark uses small four‑cylinder engines, and the exact capacity can vary slightly by engine version and whether a filter change is performed. The figures below reflect common configurations found in the 2017 Spark lineup.
- 1.2-liter engine: about 3.7 quarts (3.5 liters) of oil when replacing the filter
- 1.4-liter engine: about 4.0 quarts (3.8 liters) of oil when replacing the filter
Keep in mind that the owner's manual lists the precise capacity for your exact VIN and market. If you have trouble locating the spec, use the dipstick to tops off to the full mark after an initial 3.7–4.0 quart fill, then recheck.
Key takeaway
In short, expect roughly 3.7–4.0 quarts depending on which engine your 2017 Spark has. Always verify with the manual or the oil filler cap for the exact figure.
Oil type and how to check the level
Use the oil grade recommended by GM for your Spark, typically a Dexos1 Gen 2 specification (often 0W-20 or 5W-30 depending on climate and exact engine). Always replace the oil filter during an oil change and ensure you pour oil gradually while monitoring the dipstick.
- Ensure you use the correct Dexos1 Gen 2 approved oil and the recommended viscosity for your climate.
- Pour in oil in stages and recheck the level with the dipstick to avoid overfilling.
- Replace the oil filter and run the engine briefly to circulate oil, then recheck once more after the engine cools.
Following these steps helps ensure the engine receives the right amount of oil and maintains proper lubrication. If in doubt, consult the owner's manual or contact a Chevrolet dealer.
How to perform a basic oil change (brief overview)
If you plan to change the oil yourself, here is a concise outline of the process. Always take safety precautions and use proper tools and a drain pan.
- Warm up the engine, then turn it off and secure the vehicle. Place a drain pan beneath the oil sump.
- Remove the drain plug and let the used oil drain completely. Replace the drain plug gasket if needed.
- Remove the old oil filter, apply a thin coat of new oil to the seal, and install the new filter.
- Pour in the recommended amount of new oil (about 3.7–4.0 quarts, depending on engine) and check the level with the dipstick after a few minutes of settling.
Dispose of used oil and the filter responsibly at an approved recycling facility. Keep receipts if you had the change performed at a shop for reference.
Bottom line and tips
For a 2017 Chevy Spark, plan on about four quarts of engine oil for a complete change with a new filter. The exact amount depends on the engine variant (roughly 3.7 quarts for the 1.2L and about 4.0 quarts for the 1.4L). Always verify with the owner's manual or the oil filler cap, use the recommended Dexos1 Gen 2 oil, and check the level on the dipstick after filling.
Summary
The 2017 Chevy Spark generally requires around 4 quarts of oil for a standard change with a new filter, with a typical range of about 3.7–4.0 quarts depending on whether the engine is 1.2L or 1.4L. Always confirm the exact capacity for your vehicle in the owner's manual, use Dexos1 Gen 2 approved oil at the recommended viscosity, and verify oil level after filling.
How many quarts oil does a 2017 Chevy Spark use?
4.2 quarts
Oil Grade: SEOC3
| Viscosity: | 5W-20, 0W-20 (All TEMPS) - SAE 5W-20 is preferred. |
|---|---|
| Capacity: | 4.2 quarts (with filter). After refill check oil level. |
| Torque: | 18 ft/lbs (Oil Drain Plug) |
| Notes: | (1) This specification has been updated from Dexos 1 Gen 2 to GM Dexos 1 Gen 3. |
How much oil do you put in a 3.6 L V6?
The oil capacity for a 3.6L V6 engine is typically 5 to 6 quarts, but it varies by vehicle model and year. For a 2020 Dodge Charger, it's around 5.9 quarts, while a 2023 Jeep Wrangler requires 5 quarts. Newer Jeeps, such as the 2016-2021 Grand Cherokee and Durango, often require 6 quarts. Always check your specific owner's manual for the most accurate information, as it can differ even within the same engine family.
- 5 quarts: Common in many models like the 2020 Jeep Wrangler and 2025 Ram 1500.
- 5.9 quarts: The capacity for some models, such as the 2020 Dodge Charger.
- 6 quarts: Required for certain vehicles, including the 2013 JK Jeep Wrangler and some 2016-2021 Grand Cherokee and Durango models.
- Check your owner's manual: This is the most reliable source for your specific vehicle's oil capacity.
- After refilling: It's important to check the oil level with the dipstick after refilling to ensure it is correct.
How many quarts of oil does a 2.4 L engine take?
And max line which is good since the oil is still settling to the oil pan i'm measuring a little fast after stopping the engine. So feel free to check again at home after a little while longer.
How many quarts does a Chevy Spark take?
4.2 quarts
Engine Oil
Capacity: 4.2 quarts (with filter).
