How many quarts of transmission fluid does a 2010 Chevy Silverado take?
The 2010 Chevy Silverado requires 4 quarts of transmission fluid to fill the transmission. This is the standard amount needed for this specific model and year of the Silverado pickup truck.
Detailed Breakdown
The 2010 Chevy Silverado is equipped with a 6L80 6-speed automatic transmission. This transmission has a total fluid capacity of 4 quarts, which is the recommended amount to fill the transmission when servicing or changing the fluid.
It's important to use the correct type of transmission fluid specified by Chevrolet for the Silverado. The recommended fluid is Dexron-VI, which is a synthetic blend transmission fluid designed for use in GM automatic transmissions.
Transmission Fluid Change Procedure
- Park the vehicle on a level surface and apply the parking brake.
- Locate the transmission fluid drain plug, usually on the bottom of the transmission case.
- Place a drain pan underneath and remove the drain plug to allow the old fluid to drain out completely.
- Once drained, replace the drain plug and tighten it securely.
- Locate the transmission fluid fill plug, usually on the side of the transmission case.
- Using a fluid transfer pump, slowly add 4 quarts of the recommended Dexron-VI transmission fluid through the fill plug until it begins to drip out.
- Replace the fill plug and tighten it securely.
- Start the engine and let it idle for a few minutes to circulate the new fluid.
- Check the fluid level and add more if necessary to bring it up to the proper level.
Following the recommended transmission fluid change interval and using the correct fluid type is essential for maintaining the health and longevity of the 2010 Chevy Silverado's transmission.
How many quarts does a 2010 5.3 take?
6 quarts
Capacity: 6 quarts (with filter). After refill check oil level.
How much transmission fluid does a 2011 Chevy Silverado 1500 5.3 take?
Fill the transmission with 6 quarts of DEXRON VI Transmission Fluid.
How many quarts of transmission fluid does a 5.3 Chevy Silverado take?
For Automatic Transmission: 6L80....AF6
| Capacity: | 6 quarts Initial Fill. |
|---|---|
| Capacity: | 6 speed Light Duty 6L80 Total Fill 12.2 quarts. |
| Capacity: | 6 speed Heavy Duty 6L80 Total Fill 12.4 quarts. |
Is it okay to just drain and fill transmission fluid?
With a flush, all the old fluid is removed by a flush machine and replaced with new fluid, allowing for optimal transmission performance. A fluid change is a drain-and-refill, with some old fluid remains in the transmission after the change, which can contaminate the new fluid — and diminish performance.
How many quarts of transmission fluid do I need for a drain and fill?
Drivers can expect to pay $125 to $250 for a transmission fluid flush service. This is approximately twice as much as a transmission fluid change. This is due in large part to the additional fluid required. A flush will take 12 to 22 quarts, while a fluid change requires 5 to 7 quarts.
Is 4 quarts enough transmission fluid?
You might need 3 to 5 quarts of fluid for a standard automatic transmission car. -Suvs or trucks may need 5 to 7 quarts or more.
How much ATF does a 4L60E hold?
The 4L60E transmission typically requires approximately 12 quarts of transmission fluid for a new installation, while a fluid change usually requires around 5 quarts of fluid.
How many quarts does a Chevy Silverado transmission take?
Automatic transmissions: 4L60-E: 11.2 quarts.
How many quarts of transmission fluid does a 2010 Silverado take?
6 quarts
Automatic Transmission Fluid
Capacity: 6 speed 6L90 Total Fill 12.4 quarts. Capacity: 6 quarts Initial Fill.
How many quarts does a 5.3 Silverado hold?
Oil Grade: SEOC3
| Viscosity: | 0W-20 (All TEMPS) |
|---|---|
| Capacity: | 8 quarts (with filter). After refill check oil level. |
| Torque: | 18 ft/lbs (Oil Drain Plug) |
