How many quarts of transmission fluid does a 2017 Chevy Spark take?
The required amount depends on the transmission type. A manual transmission typically takes about 2.5 quarts, while an automatic transmission generally requires around 7.5 quarts for a full refill. For the exact figure on your specific vehicle, consult the owner’s manual or a GM service manual.
Understanding the transmission options in the 2017 Spark
The 2017 Chevrolet Spark was offered with two main transmission choices in most markets: a 5-speed manual and a 4-speed automatic. Capacities vary depending on whether you’re performing a simple drain-and-fill or a full service that may include a filter change and torque converter considerations. The figures below are general guidelines to help you plan maintenance.
Manual transmission capacity
- Approximately 2.5 quarts of manual transmission fluid.
Conclusion: For the manual version, plan on about 2.5 quarts for a standard drain-and-fill or refill. Always verify with the vehicle’s service documentation and use the recommended fluid type.
Automatic transmission capacity
- Typically about 7.5 quarts for a full service (pan drain, fluid change, and any filter replacement).
- If performing only a simple drain-and-fill, expect roughly 4–5 quarts of new fluid.
Conclusion: The automatic transmission on a 2017 Spark generally requires around 7.5 quarts for a full service, with around 4–5 quarts for a basic drain-and-fill. Always use the recommended Dexron VI fluid and follow proper service procedures.
How to check and refill transmission fluid
Before servicing, ensure the engine is warm, the vehicle is on level ground, and you have the correct fluid specification. The dipstick procedure and exact steps can vary by transmission, so refer to the owner's manual for the proper method.
- Identify your transmission type (manual or automatic) to determine the correct capacity and procedure.
- For a simple drain-and-fill: warm the engine, raise the vehicle, remove the drained fluid pan bolts, drain, replace the pan gasket if needed, and reinstall with new fluid up to the indicated fill line.
- For a full-service transmission: drain the pan, replace the filter if applicable, refill with the full specified amount (about 7.5 quarts for automatic), and check level according to the manual.
- Run the engine, shift through all gears, and recheck the fluid level when the transmission is warm on level ground.
Conclusion: Follow the vehicle’s service guidance for the correct procedure and fluid quantity. Using Dexron VI and avoiding overfill are important for proper transmission operation.
What fluid to use
GM generally specifies Dexron VI for automatic transmissions in modern Chevy vehicles, including the Spark. Always confirm the exact specification in your owner’s manual, and ensure the fluid you buy meets the Dexron VI standard or the exact specification listed for your model year and transaxle.
Summary
In summary, the 2017 Chevy Spark’s transmission fluid capacity varies with the transmission type: about 2.5 quarts for a manual and roughly 7.5 quarts for a full automatic service (about 4–5 quarts for a drain-and-fill). Always consult your owner’s manual or GM service documentation for the precise amount and use Dexron VI ATF as recommended, following proper service procedures for your specific vehicle configuration.
How many quarts of transmission fluid do I need for a drain and fill?
For a standard transmission fluid drain and fill, you'll typically need 3 to 5 quarts, but you should always measure the amount you drained and refill with the same amount to start, then check the level using the dipstick after running the engine. The exact amount varies by vehicle, and it's crucial to check the owner's manual or look up specifications for your specific make and model, as a drain and fill will not replace all the old fluid.
How to determine the right amount
- Drain the old fluid: Let the old fluid drain completely.
- Measure the drained fluid: Measure how much fluid was drained. This is your starting point for refilling.
- Refill with the measured amount: Put the same amount of new, correct transmission fluid back into the transmission. Using a funnel can help with this process.
- Start the engine: Start the vehicle and let it run for a few minutes, shifting through all the gears (Park, Reverse, Neutral, Drive) while holding the brake. This circulates the new fluid.
- Check the level: Turn the engine off and check the fluid level with the dipstick. Add more fluid in small increments if the level is low, or drain a small amount if it's too high.
- Re-check: Repeat the process of running the engine and checking the dipstick until the fluid level is correct according to the dipstick's hash marks for a "hot" reading.
Important considerations
- A drain and fill is different from a full transmission flush, which requires significantly more fluid (10-12 quarts or more) because it aims to replace all the fluid, including what's in the torque converter.
- You should always use the specific type of transmission fluid recommended by your vehicle's manufacturer to avoid damage.
- Some vehicles, like certain Land Rovers, do not have a dipstick and require a fluid extractor to add new fluid. Consult your owner's manual to be certain.
How much transmission fluid does a Chevy Spark hold?
The Chevy Spark transmission fluid capacity varies by year and transmission type, but for most automatic (CVT) models, the total fill is around 6.6 quarts. A typical "drain and fill" will require about 4.5 to 5.3 quarts of fluid, while a full system flush can use up to 10 quarts. For manual transmissions, the capacity is about 3.8 to 4.4 pints.
This video demonstrates how to change the transmission fluid on a Chevy Spark: 59sSKPcarsYouTube · Jul 6, 2024
Automatic (CVT) Transmission
- Total fill: Approximately 6.66.66.6 quarts
- Drain and fill: Roughly 4.54.54.5 to 5.35.35.3 quarts
- Full flush: Up to 101010 quarts
Manual Transmission
- Capacity: 3.83.83.8 to 4.44.44.4 pints
Important considerations
- Always check your owner's manual: for the exact specifications for your vehicle's year and model.
- When a "drain and fill" is performed, not all of the fluid is removed, so you will need less than a full system fill.
- When purchasing fluid, it is recommended to get slightly more than the estimated need for a "drain and fill" in case of spills or for topping off.
How many quarts does a 2017 Chevy Spark take?
Oil Grade: SEOC3
| Viscosity: | 5W-20, 0W-20 (All TEMPS) - SAE 5W-20 is preferred. |
|---|---|
| Capacity: | 4.2 quarts (with filter). After refill check oil level. |
| Torque: | 18 ft/lbs (Oil Drain Plug) |
| Notes: | (1) This specification has been updated from Dexos 1 Gen 2 to GM Dexos 1 Gen 3. |
How do you check transmission fluid in a 2017 Chevy Spark?
Ensure the car is in park before turning it off and exiting to pop the hood. Locate the transmission fluid dipstick under the hood; it's typically situated to the right of the oil dipstick in front-wheel-drive cars.
