How much oil does a 2013 Acura TL 3.7 take?
The 2013 Acura TL with the 3.7-liter V6 takes about 5 quarts of engine oil when performing a full change with a new filter (roughly 4.7 liters). This is the typical amount you’ll need to replenish the engine to its proper level.
Oil capacity and variation
Key numbers and scenarios you should know include the base capacity, how a new filter affects the amount of oil required, and how much oil you should add during a top-up. The following list provides typical measurements.
- Engine oil capacity with the filter installed: approximately 5 quarts (4.7 liters).
- Recommended viscosity: 5W-20 for most conditions; 5W-30 may be used where specified by the owner's manual or for hotter climates.
- Oil specification: ILSAC GF-5 or newer, API SN or newer.
These figures apply to most 2013 TL 3.7L vehicles. Always verify exact requirements in your owner's manual or the under-hood oil specification label, as there can be market-specific or model-year variations.
How to perform a proper oil fill and check
To ensure you fill to the correct level and avoid overfill, follow these steps during an oil change.
- Warm up the engine briefly, then park on a level surface and turn off the engine.
- Drain the old oil by removing the drain plug and allow it to completely drain into a suitable container.
- Remove and replace the oil filter; lubricate the gasket with a small amount of fresh oil.
- Reinstall the drain plug with a new washer if required; pour in approximately 4.5–5 quarts of fresh oil through the oil fill cap using a funnel.
- Replace the fill cap, start the engine and run for 1–2 minutes to circulate the oil; turn off and wait a few minutes for the oil to settle.
- Check the oil level with the dipstick on level ground; add small amounts of oil as needed until the dipstick shows the full mark.
- Dispose of used oil and the filter responsibly at an approved recycling facility.
Be careful not to overfill; overfilling can cause foaming and engine damage. If in doubt, consult a professional mechanic or the owner's manual for exact guidance.
Climate considerations
In very hot climates or under heavy load, you may be advised to use a different viscosity (for example 5W-30) if specified by your manual or the vehicle’s service data. Always follow the manual’s guidance for your market.
Summary
For the 2013 Acura TL with the 3.7-liter V6, plan on about 5 quarts of engine oil for a full change with a new filter (roughly 4.7 liters). The standard viscosity is 5W-20 for most conditions, with 5W-30 acceptable where the manual or climate dictates. Always verify exact specifications in your owner's manual and confirm oil level with the dipstick after servicing. Proper disposal of used oil and filters is essential.
How many quarts of oil does a 3.7 L V6 take?
A 3.7L V6 engine typically requires 6 quarts of oil, including the oil filter. However, the exact amount can vary slightly depending on the vehicle, so it is always best to check your owner's manual for the most accurate information for your specific make and model.
- Capacity: Most 3.7L V6 engines, such as those found in many Ford and Jeep models, require about 6 quarts of oil when replacing the filter.
- Verification: After refilling, always check the dipstick to ensure the oil level is correct. Do not overfill.
- Owner's Manual: To confirm the exact oil capacity and the correct oil viscosity for your specific vehicle, consult your owner's manual.
How much oil does a 2013 Acura TL take?
The 2013 Acura TL oil capacity is 4.5 quarts for the 3.5L engine and 6.0 quarts (5.7 L) for the 3.7L engine, both when changing the filter. For the 3.5L, if you do not replace the filter, the capacity is 4.2 quarts, and for the 3.7L, if you do not replace the filter, the capacity is 5.7 quarts. Always check the owner's manual and the dipstick to ensure the correct level after filling.
2013 Acura TL oil capacity by engine
| Engine Size | Capacity with filter | Capacity without filter |
|---|---|---|
| 3.5L | 4.5 quarts | 4.2 quarts |
| 3.7L | 6.0 quarts (5.7 L) | 5.7 quarts |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_ldIlafmXNvO6i-gPwPCXqAk_136';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
Additional notes
- Recommended oil: Use 0W-20 viscosity oil for the 3.5L engine.
- Drain plug torque: The oil drain plug torque specification is 29 ft-lbs for both engines.
- Final check: After refilling, always check the oil level with the dipstick to ensure it is correct and add more if needed.
Can I use 5w30 instead of 5w20 in my Acura?
Everywhere else in the world besides the US, depending on climate, Acura/Honda suggests different viscosities in our J32/J35 engines, ranging from 5w20-10w40. These engines were designed to run on 5w30. You aren't going to hurt anything. Especially if you live somewhere hot.
How much oil does a 2013 Acura 3.7 take?
Capacity: 4.5 quarts (with filter). After refill check oil level.
