How much oil does a 2018 3.5 EcoBoost take?
The 2018 Ford F-150 with the 3.5L EcoBoost V6 engine requires 6 quarts of 5W-20 engine oil for a standard oil change. This is the recommended oil capacity and type for this specific engine model.
Detailed Answer
The 2018 Ford F-150 with the 3.5L EcoBoost V6 engine is a popular full-size pickup truck. This turbocharged direct-injection engine is known for its impressive power and fuel efficiency. When it comes to the oil requirements for this engine, Ford specifies that it takes 6 quarts of 5W-20 engine oil for a standard oil change.
The 5W-20 oil weight is recommended by Ford for optimal performance and protection of the 3.5L EcoBoost engine. This oil weight provides the right balance of flow at low temperatures during cold starts, as well as the necessary viscosity at higher operating temperatures. Using the correct oil type and quantity is important to ensure the engine receives proper lubrication and meets Ford's warranty requirements.
Oil Change Procedure
- Locate the oil drain plug, usually on the bottom of the oil pan, and place a drain pan underneath.
- Unscrew the drain plug and allow the old oil to fully drain out.
- Once drained, replace the drain plug and tighten it securely.
- Locate the oil filter, typically accessible from the top of the engine, and remove it using an oil filter wrench.
- Apply a thin coat of new oil to the gasket of the new oil filter, then screw it on until secure.
- Unscrew the oil fill cap and pour in 6 quarts of new 5W-20 engine oil.
- Replace the oil fill cap and start the engine to circulate the new oil.
- Check the oil level using the dipstick and add more oil if necessary to bring it to the full mark.
Following these steps will ensure your 2018 Ford F-150 with the 3.5L EcoBoost engine is properly serviced with the right amount and type of engine oil.
Can I put 5w30 instead of 5w20?
Using 5W-30 instead can reduce fuel economy and impede flow throughout the engine. While using it temporarily in a pinch likely won't cause your engine lasting harm, remember that the engineers who built your engine did so with a specific viscosity oil in mind, meaning it's best to stick with it.
How many quarts of oil does a 3.5 L Eco Boost take?
6.0 qt
Capacities and Specifications - 3.5L Ecoboost
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 6.0 qt (5.7 L) |
| Engine coolant | 13.1 qt (12.4 L) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear axle fluid (four-wheel drive) | 2.11 pt (1.0 L) |
Does a turbo need full synthetic oil?
A Synthetic Lubricant and Synthetic Filter Combo is the Best Protection for Modern Gas Engines with Turbochargers.
How much oil does a Ford 3.5 non turbo hold?
Capacities and Specifications - 3.5L Duratec
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 6.0 qt (5.7 L) |
| Engine coolant (without trailer tow) | 13.1 qt (12.4 L) |
| Engine coolant (with trailer tow) | 13.4 qt (12.7 L) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
How many miles per gallon does a 2018 f150 3.5 EcoBoost get?
This new 2018 F-150 is rated at 21 mpg combined (19 city/24 highway), but beyond that we suspect the 10-speed automatic and the specific revisions made to its EcoBoost V6 could also close the gap between its laboratory-derived ratings and our real-world observations.
What kind of oil does a 2018 Ford F-150 take?
Ford F-150 Oil Type
Most F-150 engines need 5W-30 oil.
How often should you change the oil in a 3.5 EcoBoost?
Every 5000 miles or once a year, with a good quality full synthetic.
Is the 2018 Ford 3.5 EcoBoost a good engine?
Ford F-150 trucks with the 3.5L Ecoboost V6 turbocharged engine are very popular for a reason. Despite their sophistication compared to naturally-aspirated powertrains, the Ford F-150 3.5L Ecoboost has proven itself to be quite reliable.
What is the fuel capacity of the 2018 Ford F-150 3.5 EcoBoost?
26.0 gal
What is the best oil for the 2018 3.5 Ecoboost?
We recommend Motorcraft® motor oil for your vehicle. If Motorcraft® oil is not available, use motor oils of the recommended viscosity grade that meet API SN requirements and display the API Certification Mark for gasoline engines.
