How much oil does a 2.4 accord take?
The typical oil capacity for a 2.4L Honda Accord is about 4.5 quarts (4.3 liters) with a new filter during a full oil change. Exact amounts can vary by model year and engine variant, so always verify with the dipstick and the vehicle’s owner manual.
In this article, we detail the common capacity figures, how the filter impacts the quantity, and practical tips for ensuring the right oil level for your 2.4L Accord.
Capacity figures for the 2.4L Accord
For the 2.4L inline-4 used in many US Accords around the 2003–2007 generation, the official capacity is usually cited as about 4.5 quarts with the oil filter installed. Because engine variants and year-to-year specifications can differ, the exact figure may vary slightly.
Note that actual capacity can depend on the specific engine variant and year. The following guidance covers common maintenance scenarios to help you plan your oil change.
The figures below reflect typical maintenance scenarios and are intended as a practical guide for most 2.4L Accords. Use them in conjunction with your owner's manual and the dipstick to ensure the correct level.
- 4.5 quarts (4.3 L) with a new oil filter during a complete drain-and-fill oil change.
- Approximately 4.0 quarts (3.8 L) if the change involves a partial drain or if the oil filter is not replaced. (Variations can occur by engine variant.)
In practice, a common approach is to start by adding 4.5 quarts, then check the level with the dipstick and top up as needed to reach the full mark.
Oil grade and verification
The viscosity recommended by Honda for many 2.4L Accords is typically 5W-20, though some climates or model years may permit 5W-30. Always follow the viscosity specified in your owner's manual for your exact model and region. After pouring the oil, run the engine a moment, turn it off, wait a few minutes, and recheck the dipstick to confirm the level is within the proper range.
Maintenance tips and quick how-to
To perform a straightforward oil change on a 2.4L Accord, keep these best practices in mind. The steps below assume you’re replacing the filter as part of the change and using the recommended viscosity.
Note: The following list outlines a typical procedure. If you’re new to DIY maintenance, consult your service manual or consider asking a professional mechanic.
- Warm up the engine, lift the car safely, and place a pan under the oil pan to catch draining oil.
- Remove the drain plug, allow the oil to drain completely, then remove and replace the oil filter.
- Install the drain plug with a clean washer and refill with the recommended oil quantity (about 4.5 quarts with filter).
- Start the engine, run it briefly, turn it off, and recheck the oil level on the dipstick; add small amounts if needed to reach the full mark.
Following these steps helps ensure you reach the correct oil level without overfilling, which can cause engine issues.
Summary
For most 2.4L Honda Accords, plan on about 4.5 quarts (4.3 liters) of engine oil for a full change with a new filter, though exact capacity can vary by year and engine variant. Use the dipstick and the owner’s manual to confirm the precise amount and viscosity (commonly 5W-20). When in doubt, start at 4.5 quarts and top up carefully after checking the level to ensure the engine runs smoothly.
How much oil for a 2014 Honda Accord 2.4 L?
The 2014 Honda Accord 2.4L engine has an oil capacity of 4.4 quarts when changing the oil filter, or 4.2 quarts if the filter is not changed. The recommended oil is 0W-20.
- Capacity with filter: 4.4 quarts
- Capacity without filter: 4.2 quarts
- Recommended oil: 0W-20
- Torque for drain plug: 30 ft-lbs
- Important: Always use a new washer on the drain bolt.
How many quarts of oil does a 2.4 Honda Accord take?
A 2.4L Honda Accord typically takes 4.4 quarts of oil with a filter change, although some older models may take slightly less or require a bit more to reach the full mark. It is recommended to purchase a 5-quart jug and fill the oil to the full mark on the dipstick after the change.
Oil capacity and tips
- With filter: 4.4 quarts
- Without filter: 4.2 quarts
- Purchase recommendation: Buy a 5-quart jug, as this will provide enough oil and leave a little extra for top-offs.
- Important: Always check the dipstick to ensure the oil level is between the two marks, and avoid overfilling.
Can I put 5W-30 instead of 5W-20 on a Honda Accord?
You can likely use 5W-30 instead of 5W-20 in your Honda Accord, but you should check your owner's manual first, as the recommended oil can vary by model year and engine. Using a slightly thicker oil is sometimes done for older or high-mileage engines, but it may slightly decrease fuel economy, as the lighter 5W-20 is often specified for better efficiency.
Potential effects of using 5W-30
- Fuel economy: Thicker oil requires more energy to pump, which can lead to a slight reduction in gas mileage.
- Engine performance: Engineers design engines for specific oil viscosities. Sticking to the recommended 5W-20 ensures optimal performance and protection according to the manufacturer's specifications.
- Engine wear: In some cases, using a heavier oil in a high-mileage engine might be beneficial, especially if you're experiencing oil consumption issues. Some mechanics recommend a 5W-30 in older Honda engines to help with this, but it can also increase engine friction if the engine wasn't designed for it.
What to do
- Check your owner's manual: The most important step is to consult your car's owner's manual for the exact oil viscosity recommendation for your specific model and engine.
- Consult a mechanic: If you're concerned about your engine's performance or have a high-mileage vehicle, a mechanic can provide advice tailored to your car's condition.
How much oil does a 2.4 L 4 cylinder engine take?
5.6 quarts (with filter).
