How much oil does a Colorado 2.9 take?
There isn’t a single oil capacity figure for a “Colorado 2.9”; the exact amount depends on the engine variant, year, and market. To get an accurate number, check the owner’s manual or confirm the engine code and use the official specification for that configuration.
In this report, we explain how to identify the correct engine configuration and the steps to verify the precise oil capacity. We also offer practical tips for checking and servicing, so you can avoid under- or over-filling your engine.
What qualifies as the Colorado 2.9?
The label “2.9” could refer to different 2.9-liter engines offered in various markets and generations. Because the Colorado lineup varied by region and year, two vehicles marketed as Colorado with a 2.9-liter engine may have different oil capacities. Always verify the specific engine code and model year to obtain the correct figure.
Key factors that influence the exact capacity
Oil capacity is not universal. The exact amount depends on the engine design (gasoline vs diesel), whether the engine uses a factory oil cooler, and whether the capacity is listed with or without the filter installed. The definitive figure sits in the official service manual or Chevrolet GM documentation for the exact engine code.
To identify the correct capacity, use the steps below. They help ensure you rely on the precise specification for your rides’s configuration.
Before proceeding with the steps, gather context about your engine and vehicle.
- Engine code and displacement: Locate the engine code (often stamped on the engine or listed on the under-hood label) and confirm it is the 2.9L variant for your market and year.
- Year and market: Note the model year and region (US, Canada, Latin America, or other markets) since capacities can differ by market regulations and equipment.
- Oil change configuration: Decide if you’re using the capacity with a filter or including any additional components (such as an oil cooler), as some charts list multiple figures.
- Official reference: Consult the Chevrolet/GM service manual or an authorized dealer for the exact capacity associated with your engine code.
With the engine code and year in hand, you can confirm the precise oil quantity required for a standard oil change with a new filter.
How to determine the exact capacity for your vehicle
Follow these steps to obtain an exact figure for your Colorado 2.9:
- Identify the exact engine code and displacement for your vehicle (check the engine block stamping or the under-hood data plate).
- Look up the official oil capacity for that engine code in the Chevrolet/GM service manual or on GM’s technical documentation site.
- Note whether the capacity is listed with or without the oil filter installed, and whether any auxiliary components (like an oil cooler) affect the total.
- If the official documentation isn’t readily accessible, contact a Chevrolet dealership’s service department with your VIN and engine code to confirm the precise capacity.
Following these steps will give you the exact oil capacity for your Colorado 2.9, ensuring you fill to the correct level during maintenance.
Practical guidance for common scenarios
As a general reference (and not a substitute for the exact specification), many 2.9-liter variants in similar GM trucks tend to fall within a multi-quart range depending on configuration. Because the Colorado lineup varied widely by market and year, always verify the exact figure for your engine code before performing an oil change.
Summary
In short, the correct oil capacity for a Colorado 2.9 is engine-code dependent. There is no universal “2.9” capacity that applies to all models. To obtain an accurate number, identify your engine code and year, consult the official GM service resources, and, if needed, contact a dealer. If you provide the exact year, market, and engine code, I can help look up the precise figure for you.
Important notes and next steps
Always use the recommended oil grade for your engine as specified by GM, and replace the oil filter during every oil change. After filling, check the dipstick with the engine off and on level ground to confirm the oil level is within the proper range.
If you’d like, share your Colorado’s year, market, and engine code, and I’ll provide the exact oil capacity for that specific configuration.
How much oil does a 2017 Chevy Colorado 2.8 take?
6 quarts
Capacity: 6 quarts (with filter). After refill check oil level.
How much oil does a 2.9 l Chevy Colorado take?
5 quarts
Oil Grade: SEO23
| Viscosity: | 5W-30 (All TEMPS) |
|---|---|
| Capacity: | 5 quarts (with filter). After refill check oil level. |
| Torque: | 19 ft/lbs (Oil Drain Plug) |
What is the gas mileage on a 2012 Chevy Colorado engine 2.9 L 4 cylinder?
EPA estimated fuel economy ranges from 18 mpg city/25 mpg highway and 21 combined for the regular cab model equipped with the four-cylinder to 14 mpg city/19 highway and 16 mpg combined for crew cabs equipped with the V8 and four-wheel drive. A properly equipped V8-powered Colorado can tow up to 6,000 pounds.
How much oil does a 2.8 Colorado take?
The oil capacity for a 2.8L Colorado is 6 quarts (5.7 liters) for the Duramax diesel engine, and 5.9 quarts for the 2.8L diesel turbo engine. Always check the owner's manual to confirm the correct capacity for your specific year and engine.
- 6 quarts (5.7 liters): This is the capacity for the 2.8L Duramax diesel engine.
- 5.9 quarts: This is the capacity for the 2.8L diesel turbo engine according to AMSOIL.
- Recommendation: Double-check your owner's manual for the most accurate oil capacity for your specific vehicle model and year.
