How much torque does a 2000 Honda CRV axle nut have?

The front axle hub nut torque for a 2000 Honda CR-V is 159 ft-lbs (215 Nm).

This figure applies to the first-generation CR-V’s front axle, covering both 2WD and AWD configurations in common factory specifications. Exact torque can vary slightly by VIN or service bulletin, so always verify against the official Honda workshop manual for your vehicle.

Torque figures to know

Before performing front-end suspension work on a 2000 CR-V, it’s important to know the primary torque specification that secures the CV axle to the hub.

• Front axle hub nut torque (2000 CR-V front, 2WD and AWD): 159 ft-lbs (215 Nm).

Variations can exist due to factory updates or VIN-specific instructions. Always cross-check the exact specification in the official service documentation for your vehicle.

Proper procedure to install the axle nut

To achieve the correct preload on the front wheel bearing and ensure safe operation, follow a careful tightening procedure.

1. Stabilize the vehicle, block the wheels, and safely raise the front for access to the axle nut.


2. Remove the wheel and inspect the axle threads and hub face for damage or corrosion.


3. Clean threads and seating surfaces; avoid introducing debris into the threads.


4. Hand-tighten the axle nut to ensure clean engagement, then switch to a calibrated torque wrench.


5. Tighten the nut to 159 ft-lbs (215 Nm) using the recommended pattern or sequence specified by the manual for this component.


6. If the manual calls for post-installation re-torque after a short break-in period, perform this check after the specified mileage or time.


7. Install any cotter pin, locking device, or retainer as required by the design and verify smooth wheel rotation without binding.

Following these steps helps ensure proper bearing preload, even wear, and long-term reliability of the front axle assembly.

Notes for AWD and model-specific cautions

Some vehicles may have variant hardware or updated service bulletins that adjust the torque specification. If your CR-V has an unusual drivetrain configuration or aftermarket changes, consult the exact Honda service bulletin or dealership data for your VIN to confirm the value before performing work.

Summary

The standard front axle hub nut torque for a 2000 Honda CR-V is 159 ft-lbs (215 Nm). This value governs the secure attachment of the CV axle to the hub and helps set bearing preload. Always verify the torque against the official factory manual for your specific vehicle configuration and follow proper tightening procedures for safety and longevity.

What is the torque on the axle nut on a Honda CRV?

The Honda CR-V axle nut torque specification varies by year and axle type: it is 181 ft-lbs for front axles on many models from 1997-2011 and rear axles on some models, while it is 242 ft-lbs for front axles on 2007-2011 models and later. For the 2005 model, the rear axle nut is 134 ft-lbs. Always confirm the exact specification for your specific vehicle year and model using a service manual, and remember to stake the nut after torquing to lock it in place.
 
This video demonstrates how to replace the CV axle shaft on a 2002-2006 Honda CR-V and torque the axle nut: 56sTRQYouTube · May 10, 2022
Torque specifications by model year

• 2002-2006: 181 ft-lbs (front axle)
• 2005 (Rear Axle): 134 ft-lbs
• 2007-2011: 242 ft-lbs (front axle) 

Important considerations

• Always verify: These are general specifications. Always consult a service manual for the precise torque value for your vehicle's year and model.
• Stake the nut: After tightening, use a hammer and punch to peen the edge of the nut into the notch on the axle to prevent it from loosening, as shown in this YouTube video. 
• Use a torque wrench: Use a calibrated torque wrench for accuracy. 
• Check after driving: For safety, re-check the torque after a short drive to ensure it has not loosened. 

This video shows how to torque a CV axle nut on a 2008 Honda CR-V: 1mAlexander B SpencerYouTube · Nov 28, 2023

What is the torque on the axle nut on a 2000 Honda Accord?

The torque for the axle nut on a 2000 Honda Accord is 181 ft-lbs for the front and 134 ft-lbs for the rear. It is crucial to use a calibrated torque wrench to tighten the nut to the correct specification to prevent premature wheel bearing failure.
 
This video demonstrates how to torque the axle nut to 181 ft-lbs on a 1998-2002 Honda Accord: 53sTRQYouTube · May 20, 2021
Torque specifications

• Front: 181 ft-lbs
• Rear: 134 ft-lbs 

This video demonstrates how to torque the axle nut to 134 ft-lbs on a 1998-2002 Honda Accord: 59sTRQYouTube · May 13, 2021
Important considerations

• Use a calibrated torque wrench: An incorrect torque can lead to premature wheel bearing wear and failure. 
• Prevent wheel spin: To achieve the correct torque, you may need to use a bar across the lug studs to hold the wheel from spinning while you apply torque to the axle nut. 
• Lock the nut: After torquing, use a punch to "peen" or stake the nut's slot into the groove on the axle shaft to lock it in place and prevent it from coming loose on its own. 

What is the torque spec for a CV axle nut?

There is no single torque spec for CV axle nuts; it varies widely by make and model, ranging from approximately 110110110 to 300300300 foot-pounds (ft-lbs) or even higher. You must consult the vehicle's specific service manual for the correct torque specification, as incorrect torque can lead to premature bearing failure or other serious problems. 
Factors influencing the torque spec

• Vehicle make and model: The specific requirements change significantly between different vehicles. 
• Wheel bearing type: Different types of bearings, like tapered versus ball bearings, have different torque requirements. 
• Hub assembly: Some hub units have pre-set preload from the factory, but proper torque is still needed for spline engagement and to reduce noise or looseness. 
• AWD vs. FWD/RWD: Torque specifications can differ depending on whether the vehicle is all-wheel drive, front-wheel drive, or rear-wheel drive. 

Why proper torque is critical

• Wheel bearing preload: The axle nut's primary purpose is to set the correct preload and geometry of the wheel bearing, which is crucial for its lifespan.
• Preventing failure: Too little torque can cause premature failure, while too much torque can cause excessive heat and pressure, also leading to failure.
• Component alignment: Proper torque ensures that the rotor, backing plate, and knuckle assembly are correctly aligned. 

How to find and apply the correct torque

1. Find the manual: Obtain the correct torque specification from your vehicle's specific factory service manual. 
2. Use a calibrated torque wrench: Use a properly calibrated torque wrench to apply the correct force. 
3. Apply torque smoothly: Apply torque in a smooth, continuous motion rather than jerking the wrench to ensure accuracy. 
4. Check other specs: Some vehicles require a multi-step process, which may include a initial tightening followed by a further rotation or a final torque after the wheels are on the ground. 

What size is the rear axle nut on a 2000 Honda CRV?

Notes: Rear, Axle Nut. M22 x 1.5 mm.