How much transmission fluid does a 2008 Crown Victoria hold?
The 2008 Ford Crown Victoria’s automatic transmission holds about 12 quarts of transmission fluid when filled to the proper level, including fluid in the torque converter. For a basic drain-and-fill, expect to replace roughly 7–9 quarts; a full service with a new filter or a flush may require about 11–13 quarts depending on the procedure.
These figures come from standard specifications for the Crown Victoria’s 4R70W/4R75E family of transmissions and are commonly cited by service manuals and maintenance guides. Fluid type matters as well; Ford generally recommends Dexron VI for late-model transmissions and Dexron III for older, depending on the exact build. Always verify your exact transmission code and follow the manufacturer’s latest guidance when topping off or fully servicing the system.
Capacity figures at a glance
The following figures reflect typical capacities used by technicians when planning a service. They differentiate between a simple drain/refill and a full service that includes a filter replacement or a flush.
- Pan capacity (drain and refill, no converter drain): approximately 7.5–8.5 quarts
- Total system capacity (including torque converter, hoses, and cooler lines): about 12–13 quarts
- Full service with filter change (and potential flush): roughly 11–13 quarts
- Recommendation for purchasing fluid: plan for about 12 quarts to cover typical service needs, with a little extra as a safety margin
Understanding these numbers helps you budget fluid purchases and plan service steps. If you’re performing maintenance yourself, having a little more on hand than the maximum estimate reduces the risk of running short mid-service.
Service considerations and tips
Fluid type and checks
Use the specification recommended for your model year and transmission variant—Dexron VI is commonly recommended for late-model Ford automatics. Check the level with the engine warm and the transmission in Park or Neutral on a level surface, following the vehicle’s dipstick procedure. If you’re near the upper or lower end of the range, add small amounts and recheck to avoid overfilling.
Practical steps for a typical service
A standard drain-and-fill usually involves removing about 7.5–8 quarts of fluid from the pan and replacing it with new fluid. If you’re replacing the transmission filter or performing a more thorough flush, plan for about 11–13 quarts, and consider inspecting the pan magnet and the filter condition as part of the service.
Summary
For a 2008 Crown Victoria, plan on roughly 12 quarts of transmission fluid for a complete fill, with 7.5–8.5 quarts for a pan drain and refill. A full service with a new filter or a flush typically requires about 11–13 quarts. Use Dexron VI where recommended and verify exact specifications for your vehicle’s transmission code. Proper planning and accurate topping off help maintain optimal transmission performance and longevity.
What transmission fluid does a 5.4 Ford take?
Capacities and Specifications - 5.4L V8
| Name | Specification |
|---|---|
| Power steering fluid and Automatic transmission fluid (U.S. and Mexico): Motorcraft® MERCON LV Automatic Transmission Fluid XT-10-QLVC | WSS-M2C938-A MERCON LV |
How much transmission fluid does a 2008 Crown Vic hold?
5 quarts
For Automatic Transmission: 4R75E....MA5
| Capacity: | 4 speed 4R75E Total Fill 13.9 quarts. |
|---|---|
| Capacity: | 5 quarts Initial Fill. |
What transmission is in a 2008 Crown Vic?
Second generation (EN114; 1998–2012)
| Second generation (EN114) | |
|---|---|
| Engine | 4.6 L 2v SOHC Modular V8 |
| Transmission | 4-speed 4R70W/E automatic 4-speed 4R75W/E automatic |
| Dimensions | |
| Wheelbase | 114.7 in (2,913 mm) 120.7 in (3,066 mm) (LWB) |
How many quarts of transmission fluid do I need for a drain and fill?
For a standard transmission fluid drain and fill, you'll typically need 3 to 5 quarts, but you should always measure the amount you drained and refill with the same amount to start, then check the level using the dipstick after running the engine. The exact amount varies by vehicle, and it's crucial to check the owner's manual or look up specifications for your specific make and model, as a drain and fill will not replace all the old fluid.
How to determine the right amount
- Drain the old fluid: Let the old fluid drain completely.
- Measure the drained fluid: Measure how much fluid was drained. This is your starting point for refilling.
- Refill with the measured amount: Put the same amount of new, correct transmission fluid back into the transmission. Using a funnel can help with this process.
- Start the engine: Start the vehicle and let it run for a few minutes, shifting through all the gears (Park, Reverse, Neutral, Drive) while holding the brake. This circulates the new fluid.
- Check the level: Turn the engine off and check the fluid level with the dipstick. Add more fluid in small increments if the level is low, or drain a small amount if it's too high.
- Re-check: Repeat the process of running the engine and checking the dipstick until the fluid level is correct according to the dipstick's hash marks for a "hot" reading.
Important considerations
- A drain and fill is different from a full transmission flush, which requires significantly more fluid (10-12 quarts or more) because it aims to replace all the fluid, including what's in the torque converter.
- You should always use the specific type of transmission fluid recommended by your vehicle's manufacturer to avoid damage.
- Some vehicles, like certain Land Rovers, do not have a dipstick and require a fluid extractor to add new fluid. Consult your owner's manual to be certain.
