How much transmission fluid does a 2.3 Ford Ranger take?
The exact amount depends on the transmission type and service you’re performing, but for the common 2.3L EcoBoost Ranger with Ford’s 10‑speed automatic, the total capacity is typically about 12.5–13 quarts, and a standard pan drain-and-fill will replace roughly 6–8 quarts. Always verify the specification for your exact year and transmission model.
Transmission options for the 2.3 Ranger
Various transmissions have been paired with the 2.3 EcoBoost engine, and each carries its own capacity and service procedure. Knowing which transmission you have is essential for routing the correct fluid type and amount.
- 10‑speed automatic (10R80) is the most common setup in recent Rangers and has the largest capacity due to the torque converter and cooler lines.
- 6‑speed manual (where offered) uses a gear oil instead of automatic transmission fluid and has a different capacity and service approach.
- Special editions or regional variants may use different transmission options.
Automatic vs manual distinctions
Automatic transmissions require ATF and have a defined fill capacity, while manual transmissions use gear oil and have separate capacity figures. Always confirm the exact specification for your model year and transmission type in your owner’s manual or a Ford service bulletin.
Because capacities can vary by year and configuration, rely on your VIN-specific specs when in doubt.
Estimated fluid capacities by variant
The following ranges reflect typical figures cited for the 2.3 EcoBoost Ranger with the 10‑speed automatic, and the manual option where applicable. Use them as a guide rather than a guaranteed figure.
- Total system capacity (including torque converter and cooler lines) for the 10‑speed automatic: about 12.5 to 13.0 quarts (roughly 12 to 13 liters).
- Pan drain-and-fill replacement: typically around 6 to 8 quarts, depending on how much remains in the torque converter and lines.
- Full fluid exchange/flush (if performed): some service shops offer a procedure that can replace most or all remaining fluid, generally in the 12–13 quarts range for the entire system.
- 6‑speed manual option: uses gear oil, not ATF; capacity varies by year and model; check the owner’s manual for exact figures.
Note: Exact figures depend on year, drivetrain, and whether a filter is serviced. Always confirm with the official Ford specification for your VIN.
Year-to-year variations
Ford sometimes changes fluid recommendations or transmission configurations across model years. If you’re working on a vintage or regional version, consult the specific service data for that vehicle to ensure accuracy.
Steps to check and refill safely
Before attempting any transmission service, verify the correct fluid type, amount, and procedure for your exact model year. Some Rangers may rely on professional service and do not have a traditional dipstick.
- Warm up the engine and transmission by driving briefly, then park on level ground and engage the parking brake.
- Check the level according to the manual: if your model has a dipstick, check with the engine running and in Park; if not, follow the service procedure provided by Ford for your VIN.
- Drain the pan, replace the filter (if applicable), reinstall the pan with a new gasket, and refill with the correct transmission fluid in stages as specified.
- Recheck fluid level after the vehicle reaches normal operating temperature and completes a few drive cycles.
Using the appropriate fluid type and quantity helps ensure proper operation and longevity of the automatic transmission. If you’re unsure about the procedure, consult a qualified technician.
Summary
For most 2.3L Ford Rangers equipped with the 10‑speed automatic, plan on a total transmission fluid capacity of about 12.5–13 quarts, with a drain-and-fill typically replacing around 6–8 quarts. Exact numbers vary by model year and transmission type, so check your owner’s manual or Ford service bulletin for your specific VIN. When in doubt, have a qualified technician perform the service to ensure proper fluid type and quantity.
How many quarts does a 2.3 Ford Ranger take?
Capacities and Specifications - 2.3L EcoBoost
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 5.7 qt (5.4 L) |
| Engine coolant | 11.6 qt (11 L) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear axle fluid | 2.4 pt (1.15 L) |
How much transmission fluid does a 2009 Ford Ranger take?
Notes: Automatic Transmission Fluid. 5 gallon.
How much oil goes in a 2019 Ford Ranger 2.3 L?
Engine Oil
Capacity: 6.2 quarts (with filter). After refill check oil level.
What kind of transmission fluid does a Ford Ranger take?
Motorcraft – Mercon LV Automatic Transmission Fluid, Smooth Gear Shifts, 1 Quart (Part No. XT10QLVC) The only parts recommended by Ford Motor Company for Ford, Lincoln and Mercury vehicles.
