How to check transmission fluid 2019 Honda Passport?

Checking the transmission fluid level in your 2019 Honda Passport is an important maintenance task that should be performed regularly to ensure the proper functioning of your vehicle's transmission. This article will guide you through the steps to check the transmission fluid in your 2019 Honda Passport.

Preparing to Check the Transmission Fluid

Before you begin, make sure your Honda Passport is parked on a level surface and the transmission is in Park (P). The engine should be running and at normal operating temperature, which typically takes about 15-20 minutes of driving.

Locating the Transmission Fluid Dipstick

The transmission fluid dipstick is usually located near the front of the engine, often near the firewall. Consult your owner's manual to determine the exact location for your 2019 Honda Passport.

Checking the Transmission Fluid Level

• Pull out the dipstick and wipe it clean with a lint-free cloth.


• Reinsert the dipstick fully, then pull it out again.


• Check the fluid level on the dipstick. The level should be between the "MIN" and "MAX" marks.


• If the fluid level is low, add the recommended transmission fluid, a little at a time, until the level is within the proper range.

Be sure to use the correct type of transmission fluid specified by Honda for your 2019 Passport. Consult your owner's manual or contact a Honda dealer for the recommended fluid type.

Considerations and Precautions

• Do not overfill the transmission fluid, as this can cause damage to the system.


• If the fluid level is significantly low, there may be a leak in the transmission system. Have your vehicle inspected by a qualified mechanic.


• Regularly checking and maintaining the transmission fluid level is essential for the longevity and proper operation of your 2019 Honda Passport's transmission.

By following these steps, you can easily check the transmission fluid level in your 2019 Honda Passport and ensure your vehicle is running smoothly. Remember to consult your owner's manual for any specific instructions or recommendations from the manufacturer.

What is the transmission problem on the 2019 Honda Passport?

Many owners of 2019—2022 Honda Passport SUVs have submitted complaints to the National Highway Traffic Safety Administration. These complaints report shifting problems, delayed acceleration, sudden or harsh acceleration and other problems related to Honda 9-speed transmissions.

How to check transmission fluid in 2019 Honda Passport?

Steps to Check Transmission Fluid

1. Turn the car on. The engine should be warmed up to check the level.
2. Find the transmission fluid dipstick.
3. Remove the dipstick and touch the fluid, moving it around between your thumb and forefinger.
4. Use a rag to wipe off the dipstick.
5. Use a funnel to bring the fluid level up to full.

How to check the transmission fluid level on a 2019 Honda Pilot?

To check the 2019 Honda Pilot transmission fluid, start the engine and let it warm up, then cycle through the gears. Turn the engine off and locate the transmission fluid dipstick, typically to the right of the oil dipstick for front-wheel drive models. Pull out the dipstick, wipe it clean, reinsert it, and pull it out again to check the level and condition against the "hot" marks on the dipstick.
 
This video demonstrates how to locate and read the transmission dipstick on a Honda Pilot: 59sLive FreeYouTube · Mar 18, 2024
Step 1: Prepare the vehicle

• Start the engine and allow it to warm up until the temperature gauge is at the halfway point. 
• While the engine is running, place the vehicle in Park and shift through all the gears (Park, Reverse, Neutral, Drive, etc.), pausing for a few seconds in each. 
• Turn the engine off. 

You can watch this video to see the proper gear shifting procedure for checking the transmission fluid: 1mRB The MechanicYouTube · Sep 25, 2024
Step 2: Locate and read the dipstick 

• Find the transmission fluid dipstick. On front-wheel drive models, it is usually to the right of the engine oil dipstick. If you cannot find it, consult your owner's manual. 
• Pull the dipstick out and wipe it clean with a lint-free cloth or rag. 
• Reinsert the dipstick completely and pull it out one more time to get an accurate reading. 

This video explains how to find the transmission dipstick on a Honda Pilot and why lining up the notch is important for an accurate reading: 58sKoolbob2YouTube · Sep 18, 2022
Step 3: Check the fluid level and condition 

• The fluid level should be between the two dots or lines on the end of the dipstick, indicated for the "hot" level. 
• The fluid should be clear and have a pinkish hue. If it appears dark, burnt, or smells burnt, it is time for a fluid change. 
• If the fluid is below the "hot" fill line, add the correct type of Honda transmission fluid a little at a time until it reaches the correct level. Do not overfill. 

How to check transmission fluid level if there is no dipstick?

To check transmission fluid without a dipstick, use the vehicle's transmission fill and check plugs, which are typically on the side and top of the transmission case, respectively. This procedure requires the engine to be running and at operating temperature, and the vehicle to be on a level surface. The fluid level is correct when it begins to trickle out of the inspection plug, or a specialized dipstick can be inserted into the fill plug to measure the level.
 
This video demonstrates how to check transmission fluid level on a vehicle with no dipstick: 53sEricTheCarGuyYouTube · Jan 11, 2019
Using the transmission fill and check plugs 

1. Warm up the vehicle: Drive the car to bring the transmission to its normal operating temperature. 
2. Park on a level surface: Ensure the vehicle is parked on a flat, level surface for an accurate reading. 
3. Locate the plugs: Find the transmission fill plug (usually on top) and the check or inspection plug (on the side of the transmission case). Consult your vehicle's repair manual for the exact locations. 
4. Check the level:
   • With the engine running, slowly loosen and remove the check plug. 
   • If fluid flows out, it indicates the level is correct, so let it flow until it becomes a trickle, and then replace the plug. 
   • If no fluid comes out, the level is low. Add fluid through the fill plug until it starts to flow out of the check plug. 
5. Add fluid (if needed): If the level is low, add the correct type of transmission fluid through the fill plug using a pump until it just begins to trickle from the check plug. 
6. Tighten the plugs: Reinstall both the check and fill plugs securely. 
7. Check for signs of damage: While checking, note the fluid's color and smell. If it looks dark, brown, or has a burnt smell, it may be time for a service. 

Alternative method: Use a specialized dipstick 

1. Purchase a universal dipstick: Buy a flexible, compatible dipstick designed for vehicles without a standard transmission dipstick. 
2. Locate the fill plug: Find the fill plug on the transmission. 
3. Check the level: With the engine running and at operating temperature, remove the fill plug and insert the specialized dipstick until it reaches the bottom of the pan. 
4. Read the fluid level: Pull the dipstick out and check the fluid level against the markings. 
5. Add fluid: If the level is low, add fluid through the fill plug and recheck until the correct level is reached.