How to do a hard reset on Dodge Charger?

If your Dodge Charger is experiencing technical issues or you need to reset the vehicle's settings, performing a hard reset can help resolve the problem. A hard reset, also known as a factory reset, will restore your Charger to its original factory settings, erasing any customized configurations or stored data. This step-by-step guide will walk you through the process of conducting a hard reset on your Dodge Charger.

Steps to Hard Reset a Dodge Charger

1. Prepare the Vehicle: Make sure your Dodge Charger is parked on a level surface and the engine is turned off.


2. Locate the Battery: Open the hood of your Charger and locate the battery. It is typically located in the front of the engine compartment.


3. Disconnect the Battery: Using a wrench, disconnect the negative (-) battery cable from the battery terminal. This will cut power to the vehicle's electrical system.


4. Wait for a Minute: Allow the vehicle to sit for approximately one minute to ensure the electrical system is fully discharged.


5. Reconnect the Battery: Reconnect the negative (-) battery cable to the battery terminal, ensuring a secure connection.


6. Turn on the Vehicle: Start the engine of your Dodge Charger. The vehicle should now be in its factory default state, with all customized settings and stored data erased.

It's important to note that performing a hard reset on your Dodge Charger will erase all personalized settings, such as radio presets, climate control preferences, and any stored diagnostic trouble codes. You may need to reconfigure these settings after the reset is complete.

Reasons to Perform a Hard Reset on a Dodge Charger

There are several reasons why you might need to perform a hard reset on your Dodge Charger:

• Troubleshooting Technical Issues: If your Charger is experiencing glitches, freezes, or other technical problems, a hard reset can help resolve these issues by clearing any underlying software or system conflicts.


• Resetting the Vehicle's Computer: The hard reset process will reboot the Charger's onboard computer, allowing it to start fresh and potentially fix any issues related to the vehicle's electronic systems.


• Preparing for Resale: If you're planning to sell your Dodge Charger, performing a hard reset can help ensure that all personal data and settings are removed, providing a clean slate for the new owner.

Remember, a hard reset should be considered a last resort for resolving technical issues with your Dodge Charger. If the problem persists after the reset, it's recommended to consult a professional mechanic or the Dodge customer support team for further assistance.

How do I hard reset my car computer?

On. Now comes the tricky. Part the computer's got to relearn. So start the vehicle. And put it in neutral. Let it run for about 4 minutes in neutral.

How to hard reset a Dodge Charger?

Hard Reset Uconnect® Instructions

1. Press the temperature up and down buttons simultaneously for at least five seconds.
2. Navigate the menu that comes up on the screen and choose the option that prompts you to reset to factory settings.
3. After choosing this option, wait about 30 seconds while the system reboots.

How do I reset a charger?

First locate the breaker switch and flip it to the off. Position. Then wait a few minutes to allow the system to reset after the waiting period switch the breaker back to the on position.

How to reset dodge charger pcm?

To reset the Dodge Charger's PCM (Powertrain Control Module), you can perform a hard reset by disconnecting both battery terminals for at least 30 minutes, or use a specialized OBD2 scanner to reset the transmission control module (TCM) or clear adaptive memory. Another method is to perform a throttle re-calibration procedure. A hard reset is a more comprehensive option, while a scanner or throttle reset are more specific and faster.
 
Hard reset (battery disconnection)

• Disconnect the negative battery terminal first, followed by the positive terminal. 
• To ensure a full discharge, connect the two battery cables together (not the terminals) for about 5 minutes. 
• Reconnect the battery terminals, positive first, then negative. 
• The vehicle will need to relearn settings, so allow it to idle for 5 minutes and then drive it normally to relearn shifting patterns. 

This video demonstrates how to disconnect the battery cables to reset your Dodge Charger's PCM: 56sFixITYouTube · Jun 18, 2025
OBD2 scanner method

• Plug an OBD2 scanner into the diagnostic port (usually under the dashboard). 
• Turn the ignition to the "on" position (without starting the engine). 
• Navigate to the transmission control module (TCM) or powertrain control module (PCM) section in the scanner's menu. 
• Select the option to clear codes, reset keep alive memory (KAM), or perform a relearn procedure. 
• After the reset, turn the ignition off for about a minute, then start the car and let it idle. 
• Take the vehicle for a test drive to allow it to relearn its driving patterns. Avoid hard acceleration for the first few miles. 

Throttle re-calibration 

• Turn the ignition key to the "on" position, but do not start the engine.
• Wait for all of the dashboard lights to turn off.
• Slowly press the accelerator pedal all the way to the floor.
• Slowly release the pedal until it is all the way back up.
• Turn the key to the "off" position and then start the engine.