How to see tire pressure on Honda Insight?

Many Honda Insights with a Tire Pressure Monitoring System (TPMS) display current tire pressures in the instrument cluster or multi-information display. If your model doesn’t show per-tire data, you’ll need to measure with a handheld gauge and refer to the door placard for the recommended pressures.

Where to view TPMS data on modern Insights

Here’s how to access tire pressures when the vehicle provides a digital readout. The exact path can vary by year and trim, but these steps cover the common setups.

• Use the steering wheel controls to cycle the instrument cluster or multi-information display to the Vehicle Information or TPMS page, where individual tire pressures may be shown.


• On some trims, the TPMS values appear only after you select a Tire Pressure screen or a Vehicle Status menu; others show them on a graphic with each tire’s PSI.


• If the TPMS warning light is on, you may still be able to view the pressures on-screen; if not, you’ll need to use a gauge and placard as described below.

These display options help you monitor inflation without pulling over and using a gauge, though not all model years provide a real-time readout for every tire.

Manual tire pressure checks when no readout is available

For Insights that don’t show per-tire pressures, you should measure cold pressures with a gauge and verify against the official spec on the door placard.

1. Find the recommended cold tire pressures on the driver’s door jamb placard or in the owner’s manual; note separate values for front and rear tires if listed.


2. Park on a level surface with the engine off and tires cold (do not measure after a drive).


3. Remove the valve stem cap, place a tire gauge on the valve stem, and read the PSI value.


4. Inflate or deflate each tire to the recommended pressure, then reseal the valve caps.


5. Re-check all four tires to ensure they’re at the specified pressure after adjustments.

Regular manual checks complement the TPMS system and help ensure even wear, better handling, and optimal fuel efficiency.

TPMS calibration and potential issues

After inflating to the correct pressure, drive normally for a short distance to allow the TPMS to recalibrate. If the warning light stays on despite correct pressures, there may be a faulty sensor or valve that needs inspection by a technician.

Practical tips and common questions

What if I don’t see any tire pressure data on my dashboard? Use a manual gauge and the door placard to set pressures; check whether your trim supports a dedicated TPMS readout. How often should you check tire pressures? At least monthly and before long trips, especially in extreme temperatures. Are tire pressures the same for all tires? No; follow the door placard for front/rear and consider differences for equal or staggered tire sizes when applicable.

Summary

In the Honda Insight, you can view tire pressures via the built-in TPMS readout on many modern trims or rely on a manual gauge when no display is available. Always start with the door placard values for the recommended cold pressures, check tires when cold, and recalibrate the TPMS after inflation if required. Regular checks help improve safety, wear, and efficiency.

Does the Honda app show tire pressure?

Convenience features available via the owner's smartphone include: Viewing the TPMS status and air pressure in each tire. Checking whether the doors are locked. A “Find My Car” feature that locates the vehicle with mapping software.

Can you check tire pressure on the dashboard?

Yes, many modern cars have a Tire Pressure Monitoring System (TPMS) that displays tire pressure on the dashboard, either through a warning light or by showing the actual pressure for each tire. Some vehicles even have a tire fill assist feature that provides audible and visual cues when you inflate the tires to the correct pressure. 
This video explains how to check your tire pressure using the TPMS system on your car: 59sVolkswagen USAYouTube · Aug 1, 2023
How to check tire pressure using your dashboard

1. Check for a warning light: Look for a horseshoe-shaped light with an exclamation point inside on your dashboard. This is the TPMS warning light, which indicates a low-pressure tire. 
2. Find the specific pressure display: Some vehicles display the pressure for each tire. You may need to navigate through the car's infotainment or digital gauge cluster menus to find this information. Check the "vehicle" or "settings" section on the display. 
3. Use the tire fill assist (if equipped): If your car has this feature, follow the instructions in your owner's manual. It typically involves putting the car in park with the parking brake engaged and then inflating a tire. The system will alert you when the correct pressure is reached. 
4. Consult your owner's manual: The exact method for viewing tire pressure will vary by car make and model, so your owner's manual is the best resource for specific instructions. 

What to do when you see a warning light

• Check your tires: Visually inspect your tires for any obvious damage and make sure they are not visibly flat. 
• Inflate your tires: Use an air compressor at a gas station to fill the tires to the recommended pressure. The correct pressure is listed on a sticker on the driver's side door jamb. 
• Check the TPMS light again: After filling the tires, drive the car for a few minutes. The TPMS light should turn off once the correct pressure is restored. 
• Visit a mechanic: If the light remains on after inflating the tires, there may be a leak or a problem with the TPMS sensors themselves. Take your car to a professional to have it inspected. 

This video shows how to check tire pressure using a physical gauge: 51sAlberta Motor AssociationYouTube · Jul 28, 2015

How to check tire pressure on Honda?

To check the tire pressure on a Honda, first find the recommended pressure on the sticker in the driver's side door jamb, then use a tire pressure gauge on each valve stem to read the current pressure. For a digital check, use the steering wheel buttons to navigate the instrument panel to the "Tire Pressure" screen in the "Maintenance" menu, which shows the pressure for each tire. 
Using a manual gauge
This video shows how to check tire pressure with a manual gauge: 1mHonda of LincolnYouTube · Nov 14, 2024

1. Find the recommended pressure: Open the driver's door and look for a sticker on the door jamb that lists the correct PSI (pounds per square inch) for your vehicle. 
2. Unscrew the valve cap: Unscrew the cap from the tire's valve stem. 
3. Press the gauge onto the valve stem: Firmly press a tire pressure gauge straight onto the valve stem. You may need to adjust slightly to get a good seal and stop the hissing sound of air escaping. 
4. Read the pressure: Read the pressure displayed on the gauge. Check each tire and repeat the process. 
5. Adjust the pressure: If the pressure is low, add air using an air compressor until the correct PSI is reached. If it's too high, release some air. 
6. Replace the valve cap: Screw the valve cap back on to the stem to keep out dirt. 

Using the built-in system

1. Turn on the car: Start the power mode of your vehicle. 
2. Navigate the display: Use the buttons on your steering wheel to scroll through the options on your driver information interface. 
3. Find Tire Pressure: Navigate to the "Maintenance" menu, then select "Tire Pressure". 
4. View each tire's pressure: The screen will show the pressure for all four tires, often indicated in PSI. A low-pressure warning will be displayed if a tire is significantly under-inflated. 

How to see tire pressure in Honda Insight?

The specified tire pressure is on a label on the driver's doorjamb.
PDF