What is the top speed of a Ford Flex?
The Ford Flex's top speed is about 120 mph (193 km/h), electronically limited in most configurations. This ceiling applies across most model years and drivetrains, with only minor variation due to tires, weight, and equipment.
Overview of speed by generation
The Ford Flex was produced from 2009 to 2019 as a family-oriented three-row crossover. While horsepower increased modestly with later engines, the top speed remained limited to about 120 mph due to safety and regulation. Official figures are not published by Ford, and estimates come from independent testing and owner reports.
Early Ford Flex models (2009–2012)
Engine and gearing snapshot
In the early years, the Flex used a naturally aspirated 3.5-liter Duratec V6. Performance tuning and gearing were designed to emphasize smooth acceleration and cargo capacity rather than top-end speed.
Note: The typical maximum speed for these models sits around 118–120 mph depending on tires and trim.
- Engine: 3.5L Duratec V6 (2009–2012) — estimated top speed around 118–120 mph (190–193 km/h).
Conclusion: Across the early generation, the top speed remained in a similar range to contemporary family crossovers.
Later Ford Flex models (2013–2019)
Performance characteristics
For 2013 and later, Ford updated the engine with the Ti-VCT configuration, maintaining similar power outputs while refining efficiency and drivability. The top speed is still limited to about 120 mph.
Note: Estimated top speed is around 118–120 mph (190–193 km/h), depending on drivetrain and tires.
- Engine: 3.5L Ti-VCT V6 (2013–2019) — estimated top speed around 118–120 mph (190–193 km/h).
Conclusion: The later generation preserves the same general top-speed ceiling as the early models, despite horsepower increments.
Practical considerations
In everyday driving, the Ford Flex prioritizes passenger comfort, cargo capacity, and highway cruising stability. Top speed is rarely reached in normal use; safety systems, weight, and tire ratings all influence how the vehicle behaves at higher speeds. Always follow speed limits and drive responsibly.
Summary
Throughout its 2009–2019 production run, the Ford Flex maintained a common top speed ceiling near 120 mph (193 km/h). While horsepower rose modestly with updates, the electronically limited maximum kept performance in a similar band across generations. For buyers and drivers, speed isn’t the primary appeal; space, comfort, and practicality define the Flex.
How fast does a Ford Flex go?
FORD Flex 3.5L V6 Duratec 6AT (262 HP)
| PERFORMANCE SPECS | |
|---|---|
| Top Speed: | 127 mph (204 km/h) |
| Acceleration 0-62 Mph (0-100 kph): | 7.8 s |
Can a Ford Flex last 300,000 miles?
Typically, you can expect a Ford Flex to last around 200,000 miles with excellent care, according to carparts.com.
What is the top speed of the 2010 Ford Flex?
With the 3.5-liter EcoBoost V-6 sending 355 hp and 350 lb-ft of torque through the standard six-speed automatic and all-wheel-drive system, our SEL tester hustled to 60 mph in six seconds flat, covered the quarter-mile in 14.6 at 96 mph, and reached a governed top speed of 123 mph.
How to remove Ford speed limiter?
To remove a Ford speed limiter, you can either use a professional diagnostic tool like Ford IDS to reprogram the PCM (Powertrain Control Module) or, on some models, adjust the "MyKey" settings through the instrument cluster. For professional removal, a mechanic uses a tool like the Ford VCM II to access the programmable parameters and disable the limiter, while clearing any error codes afterward. If your vehicle has the "MyKey" feature, you can clear these settings using an admin key by navigating through the vehicle's settings menu.
Method 1: Professional reprogramming (e.g., using Ford IDS)
This method is used for factory-installed speed limiters that are not part of the "MyKey" system.
- Access the programming menu: Connect the diagnostic tool (like a VCM II) to the vehicle and launch the Ford IDS software.
- Navigate to the speed limiter settings: Go to the "Toolbox," then "Module Programming," followed by "Programmable Parameters" and "Speed Items".
- Disable the speed limiter: Select "Vehicle Speed Limit (PCM)" and choose the option to "Disable Speed Limiter".
- Complete the reprogramming: Follow the on-screen instructions to erase the old data and program the new calibration. Cycle the ignition on and off as prompted.
- Clear error codes: After programming is complete, clear any Diagnostic Trouble Codes (DTCs) that may have been set.
This video demonstrates how to remove the speed limiter using Ford IDS software: 59sTool Hut USAYouTube · Dec 25, 2024
Method 2: Clear "MyKey" settings
This method is for vehicles that use the "MyKey" system to create a speed-limited key.
- Start with an admin key: Turn on the vehicle using a key that is not a "MyKey".
- Access the settings: Use the steering wheel controls to navigate to the "Settings" menu on the information display.
- Find MyKey: Scroll to and select the "MyKey" option.
- Clear MyKey: Choose the "Clear MyKey" option and then press and hold the OK button until a message confirms that all MyKeys have been cleared.
You can watch this video to learn how to clear MyKey settings: 56sShaners Mechanic LifeYouTube · Jul 27, 2025
This video shows how to clear the speed limiter from MyKey settings: 58sDIYrepair CornerYouTube · Jan 24, 2023
Important considerations
- Professional help: If you are not comfortable with the technical steps, it is best to have a qualified mechanic or dealership perform the procedure.
- Vehicle variations: The exact steps and menu options may vary depending on the Ford model and year.
- Potential consequences: Disabling the speed limiter can cause excessive wear on the vehicle's components, potentially leading to costly repairs.
