What size are the lug nuts on a 2017 Honda Fit?
The lug nuts on a 2017 Honda Fit use M12 x 1.5 threads with a 19 mm hex head and a conical (tapered) seat, fitted to a 4x100 bolt pattern. Tighten to about 80 ft-lb (108 Nm) with a 19 mm socket or lug wrench.
Key lug nut specifications for the 2017 Fit
Below are the essential hardware specs you should know for the factory lug nuts, plus guidance for aftermarket wheels.
- Thread size: M12 x 1.5
- Seat type: conical (tapered) seat
- Bolt pattern: 4x100 mm
- Outer hex size: 19 mm
- Recommended torque: 80 ft-lb (108 Nm)
These specifications are standard for the 2017 Fit’s original equipment wheels, but always verify with your wheel or lug nut supplier if you’re using aftermarket parts, as some combinations use different seat types or hex sizes.
Fitting aftermarket wheels or replacements
When selecting wheels or lug nuts beyond the factory setup, confirm compatibility across several dimensions to ensure proper fit and safety.
- Verify the wheel bolt pattern matches 4x100 mm on the vehicle.
- Confirm lug nut thread size and seat type match the wheel and studs (typically M12 x 1.5 with conical seats).
- Ensure the outer hex size matches your socket (commonly 19 mm for this vehicle).
- Adhere to the correct torque specification and recheck torque after installation (see below).
- Check center bore compatibility and hub-centric fit if applicable.
Following these checks helps prevent wheel seating issues, hub misalignment, or loose lug nuts after driving.
Additional tips and safety notes
To keep wheels and lug nuts secure and prevent damage, observe these guidelines. Do not overtighten or use anti-seize compounds on lug nuts unless explicitly recommended by the wheel or vehicle manufacturer. After installation, re-torque the lug nuts after about 50 to 100 miles (80 to 160 kilometers) to account for settling and ensure long-term security.
Summary
The 2017 Honda Fit uses M12 x 1.5 lug nuts with a 19 mm hex, cone-seat design, on a 4x100 bolt pattern. Tighten to about 80 ft-lb (108 Nm) and verify compatibility with any aftermarket wheels by ensuring matching thread, seat type, bolt pattern, and proper torque. Always recheck torque after a short drive and refer to OEM or wheel manufacturer guidance for any deviations.
What size are the lug nuts on a Honda Fit?
The lug nut size for a Honda Fit is M12 x 1.5 (metric 12mm diameter with a 1.5mm thread pitch), which is standard for all model years. It is crucial to ensure you also get the correct seat style (usually conical) and length, as well as the proper hex size (commonly 19mm or 3/4 inch for the socket) to fit your specific wheel and ensure a safe installation.
Key specifications
- Thread size: M12 x 1.5
- Diameter: 12mm
- Pitch: 1.5mm
- Seat style: Typically conical
- Hex size: Commonly 19mm or 3/4 inch (check your owner's manual or a lug nut from your current wheel for confirmation)
Important considerations
- Seat style: Lug nuts come in different styles, such as conical, spherical, and mag shank. Ensure the new lug nut matches the seat style of your wheel for a secure fit.
- Length: The overall length of the lug nut can vary. Choose a length that is appropriate for your specific wheels, especially if you are using aftermarket wheels.
- Hex size: The hex size is the measurement for your socket. While 19mm or 3/4 inch is common for Honda Fits, it is best to verify the correct size for your vehicle.
- Torque: Always torque the lug nuts to the manufacturer's specified torque value, which is 80 foot-pounds for the 2009-2013 Honda Fit.
- Cross-threading: When installing new lug nuts, be careful not to cross-thread them by hand-tightening them first to ensure they are going on straight.
What size socket for Honda lug nuts?
What Size Honda Lug Nuts Do I Need?
| Model | Year | Thread/ Socket Size |
|---|---|---|
| Accord | 2003-2020 | 19 mm |
| Civic | 2006-2020 | 19 mm |
| CR-V | 1997-2020 | 19 mm |
| Pilot | 2003-2020 | 21 mm |
What size are the lug nuts on a 2017 Honda?
12 mm x 1.50 thread size, 3/4" and 13/16" hex.
Can I use 7/8 socket for 22mm?
Yes, you can use a 7/8" socket for a 22mm bolt or nut because they are the same size, with a very small difference that is negligible in practice. 22mm is equal to approximately 0.8660.8660.866 inches, and 7/87 / 87/8 inch is equal to 0.8750.8750.875 inches.
- Size conversion: The two sizes are effectively interchangeable, as they are the closest imperial and metric equivalents.
- Fit: A 7/87 / 87/8" socket will fit on a 22mm bolt. It may feel a little loose, but it will still work.
- Impact tools: This combination is commonly used for impact tools, like those for lug nuts, where sockets are often stamped with both sizes.
- Warning: It's important to use a socket with the correct number of points (e.g., 6-point or 12-point) to avoid damaging the bolt or nut, especially on older or rounded-off fasteners.
