What size are the lug nuts on a RAV4?
The typical lug nut specification for most modern RAV4 models is M12 x 1.5 with a 60-degree conical seat, a 5x114.3 mm bolt pattern, and a 19 mm hex size for the lug wrench. Torque is generally around 76–80 ft-lb (103–108 Nm). Always verify for your exact year and wheel configuration.
Common specifications across recent RAV4 models
Thread size, seat type, and hex size
Below are the specifications you’ll commonly encounter on recent RAV4s. These cover the standard factory wheels found on most trims, though variations can occur with different wheels or aftermarket setups.
- Bolt pattern: 5x114.3 mm (5 on 4.5 inches)
- Lug nut thread size: M12 x 1.5
- Lug nut seat type: 60-degree conical (acorn) seat
- Hex size for lug wrench: typically 19 mm (some wheels or aftermarket nuts may require a different size)
- Typical torque specification: about 76–80 ft-lb (103–108 Nm)
These specifications apply to many recent RAV4 generations, but exact details can vary by year, trim, and wheel package. If you have aftermarket wheels or a nonstandard trim, your lug nut size may differ.
How to verify for your vehicle
Steps to confirm lug nut size
If you want to confirm your exact lug nut size for your RAV4, follow these steps to be sure you’re buying the right hardware.
- Check the vehicle’s owner’s manual or the door jamb placard for the wheel lug nut specification and torque value.
- Inspect the lug nuts themselves for stamped size, part numbers, or markings that match Toyota parts catalogs.
- Measure the hex across the flats of the lug nut with a caliper or ruler to confirm the correct socket size (most are 19 mm on modern Toyota wheels, but some setups may differ).
- When in doubt, bring a sample lug nut or the wheel/tactory lug wrench to a dealership or auto parts store for confirmation.
Accurate verification helps prevent cross-threading or under/over-tightening, which can affect wheel safety and tire wear.
Why lug nut size matters
Using the correct lug nut size and torque is essential for wheel retention and road safety. An incorrect size can strip the nut or wheel studs, damage the wheel, or lead to looseness while driving. Always follow the manufacturer’s specifications or consult a qualified technician if you’re uncertain.
Summary
For most modern Toyota RAV4s, expect lug nuts that are M12 x 1.5 with a 60-degree conical seat, a 5x114.3 mm bolt pattern, and a 19 mm hex size, torqued to roughly 76–80 ft-lb (103–108 Nm). Because variations exist across model years and wheel packages, verify with the owner’s manual, door placard, or Toyota parts documentation to ensure exact compatibility for your vehicle.
Can I use 7/8 socket for 22mm?
Yes, you can use a 7/8" socket for a 22mm bolt or nut because they are the same size, with a very small difference that is negligible in practice. 22mm is equal to approximately 0.8660.8660.866 inches, and 7/87 / 87/8 inch is equal to 0.8750.8750.875 inches.
- Size conversion: The two sizes are effectively interchangeable, as they are the closest imperial and metric equivalents.
- Fit: A 7/87 / 87/8" socket will fit on a 22mm bolt. It may feel a little loose, but it will still work.
- Impact tools: This combination is commonly used for impact tools, like those for lug nuts, where sockets are often stamped with both sizes.
- Warning: It's important to use a socket with the correct number of points (e.g., 6-point or 12-point) to avoid damaging the bolt or nut, especially on older or rounded-off fasteners.
What size socket for Toyota lug nuts?
The socket size for most Toyota lug nuts is 21mm or 13/16". However, the 21mm socket is for the inner lug nut, and a 13/16" socket may not fit if the decorative cap has become damaged or swollen. Newer models, such as the 2023 Tacoma, may require a 22mm socket. To confirm the exact size for your vehicle, check the lug nut's specification or use a tire iron or adjustable wrench to measure the nut.
Recommended socket sizes
- Standard Toyota: Use a 21mm or 13/16" socket for most standard Toyota vehicles.
- Larger Toyota models: Newer models like the 2023 Tacoma may require a 22mm socket.
How to confirm the size
- Check specifications: If possible, find the lug nut's specifications or use the vehicle's manual to determine the correct size.
- Measure: Use a tire iron or an adjustable wrench to measure the lug nut's size.
- Use a tool: Take a lug nut to a hardware store or auto parts store and try it in a socket to find the right fit.
What size are Toyota Rav4 lug nuts?
The lug nut size for a Toyota RAV4 is M12 x 1.5 for all models from 1994 to 2025. This applies to the thread size, which is 12mm in diameter with a 1.5mm pitch. The socket size needed is typically 21mm, but can sometimes be 13/16" for aftermarket nuts.
Key specifications
- Thread Size: M12 x 1.5
- Socket/Wrench Size: 21mm or 13/16"
- Torque: 103 Nm (76 ft-lb)
What is the bolt size of a Toyota Rav4?
5×114.3mm
The Toyota RAV4 maintains the standard Toyota SUV bolt pattern of 5×114.3mm across all trim levels.
