What size is a Honda oil drain plug?
The standard size of a Honda oil drain plug is 17 mm. This is the most common size used across Honda's vehicle lineup, though some models may have slightly different sizes. The oil drain plug is a crucial component that allows you to easily change the engine oil in your Honda vehicle.
Understanding the Oil Drain Plug Size
The oil drain plug is located at the bottom of the oil pan and is responsible for allowing the old oil to drain out when performing an oil change. Honda typically uses a 17 mm hex head oil drain plug, which is a standard size found in many vehicles. This size allows for easy removal and reinstallation of the plug using a 17 mm wrench or socket.
It's important to note that while 17 mm is the most common size, some Honda models may use slightly different sizes, such as 19 mm or 14 mm. It's always best to consult your owner's manual or check the size of the existing plug before attempting an oil change to ensure you have the correct replacement part.
Replacing the Oil Drain Plug
- Locate the oil drain plug, usually at the bottom of the oil pan.
- Use a 17 mm wrench or socket to loosen and remove the plug.
- Allow the old oil to fully drain from the oil pan.
- Clean the threads on the oil pan and the plug to ensure a proper seal.
- Apply a small amount of thread sealant or oil to the threads of the new plug.
- Reinstall the plug and tighten it securely, but do not overtighten.
- Check for any leaks after the oil change is complete.
Replacing the oil drain plug is a straightforward task, but it's important to use the correct size to ensure a proper fit and prevent any leaks. Always refer to your Honda's owner's manual or consult a professional if you're unsure about the specific size or procedure.
What size socket is the oil drain plug on a Honda CRV?
17Mm
Dorman – Oil Drain Plug Standard M20-1.50, Head Size 17Mm (Part No. 65221)
Are all oil drain bolts the same size?
It's called the oil drain plug, and there is no single size. There are hundreds of different sizes. The auto parts store will be able to tell you what size you have, based on year, make, model, and engine, and can get you a replacement plug. Make sure you know whether your car uses metric or SAE, too.
What size socket fits an oil drain plug?
3/8-inch
Place a 3/8-inch (0.9 centimeters) socket in the socket wrench, fit it over the drain plug's nut and turn it counterclockwise. The oil drain plug should open easily, draining the used oil from the engine. Make sure to place a bucket and some newspaper under the car's engine to catch all the draining oil.
What size is the oil pan bolt on a Honda Accord?
5 for Honda Accord Civic CR-V Fit Odyssey.
What size is the oil drain plug on a Honda B Series?
Oil Drain Plug - Oem Type - 14 mm - 1.5.
Are all Honda drain plugs the same size?
14 mm. It is the same as on all the Hondas and Acuras.
How do I know what size drain plug I have?
Measure the width of the plug at the widest part of the threads. If your plug measures 12mm you will need to start looking at plugs in the size range of “M12 x 1.25 to M12 x 1.75″. The “M12” refers to the diameter you measure from the widest part of the threads on your OEM sump plug.
What size wrench for Honda oil drain plug?
The drain plug is located on the back of the oil pan and takes a 17mm socket or wrench.
How to know drain plug size?
Measure Diameter
Measure the width of the plug at the widest part of the threads. If your plug measures 12mm you will need to start looking at plugs in the size range of “M12 x 1.25 to M12 x 1.75″. The “M12” refers to the diameter you measure from the widest part of the threads on your OEM sump plug.
What size is the oil drain plug on a Honda?
5 Oil Drain Plugs M14-1.5 17mm Hex Compatible with Acura & Honda.
