What size is the drain bolt on a 2010 Honda Pilot?
The drain bolt size on a 2010 Honda Pilot is 17mm. This is the standard size for the oil drain plug on this model year of the Honda Pilot SUV.
Detailed Information on the 2010 Honda Pilot Drain Bolt
The 2010 Honda Pilot is a mid-size SUV that was produced by Honda. When it comes time to change the oil, the drain bolt that needs to be removed is a 17mm size. This is a common size for many Honda and Acura vehicles from this era.
To change the oil on a 2010 Honda Pilot, you will need the following tools:
- 17mm socket or wrench
- Oil filter wrench
- Oil drain pan
- New oil filter
- Recommended engine oil
Once you have the necessary tools, you can follow these steps to change the oil:
- Park the Pilot on a level surface and apply the parking brake.
- Locate the oil drain plug, which is typically located on the bottom of the oil pan.
- Using the 17mm socket or wrench, loosen and remove the drain plug, allowing the old oil to drain out.
- Once the oil has fully drained, replace the drain plug and tighten it back up using the 17mm tool.
- Locate the oil filter, typically accessible from the top of the engine, and use the oil filter wrench to remove it.
- Apply a thin coat of new oil to the gasket of the new filter, then screw it on by hand until secure.
- Refill the engine with the recommended amount and type of new oil.
- Start the engine and check for any leaks around the drain plug or oil filter.
By following these steps and using the correct 17mm drain bolt size, you can successfully change the oil on your 2010 Honda Pilot.
What size socket is my drain plug?
What size wrench to use for an oil drain plug depends on the size of the oil drain plug itself, which is a long bolt head. There is no universal oil plug size, but they do come in just a few several standard sizes, such as ¼ inch (. 6 centimeters), 3/8 inch (. 9 centimeters), ½ inch (1.3 centimeters), etc.
Are oil drain plugs the same size?
All drain plugs are not the same because all drain pans are not the same. OE manufacturers have different designs when it comes to their vehicle, so naturally, oil drain pans, drain plugs and gaskets are different too.
What size socket is a Honda drain bolt?
Oil drain pan opening is a 14mm diameter opening. Oil drain plug is an M14, this takes thread count and "pitch" (the "aggressiveness" of the the angle of the threads) into account. The "head" of the oil drain plug is 17mm. So to remove/install the engine oil drain plug, you will need a 17mm socket or wrench.
Does Honda use metric or SAE bolts?
Most Honda hardware is comparable to metric grade 10.9 or higher. Steps To Knowing Your Bolts: When determining bolt sizes, look to the numbers. Manufacturers use them for identification purposes.
What size wrench do I need to remove the oil drain plug?
Place a 3/8-inch (0.9 centimeters) socket in the socket wrench, fit it over the drain plug's nut and turn it counterclockwise.
Are all Honda drain plugs the same size?
The engine oil drain plugs have always been 14mm x 1.5 with a 17mm head, and the transmission oil drain plugs have been 18mm (x 1.5 also I think) with a 3/8" square drive.
How to find out oil drain plug size?
Measure Diameter
Measure the width of the plug at the widest part of the threads. If your plug measures 12mm you will need to start looking at plugs in the size range of “M12 x 1.25 to M12 x 1.75″. The “M12” refers to the diameter you measure from the widest part of the threads on your OEM sump plug.
What size is the oil drain plug on a 2006 Honda Pilot?
No need; drive it on some good height ramps, grab a 17mm socket and ratchet (or a 17mm wrench) and drain your oil from the oil pan (towards your front right wheel).
What is the torque on the drain plug on a 2010 Honda Pilot?
29 ft/lbs
Torque: 29 ft/lbs (Oil Drain Plug) Install a new washer on the drain bolt. Only use an OE drain plug.
How many quarts does a 2010 Honda Pilot take?
4.5 quarts
Fluids and Capacities
Capacity (with filter) is 4.5 quarts (4.3 liters). (Note: The oil drain bolt should be tightened to 29 pound-feet (39 N-m) of torque.)
