How much oil does a 2018 Chevy Colorado V6 take?
The 2018 Chevy Colorado with the 3.6L V6 uses about 6 quarts (5.7 liters) of engine oil when you perform a full oil change with the filter, using Dexos1 Gen 2, 5W-30 motor oil. This article explains that capacity, the recommended oil type, and how to verify levels for proper maintenance.
Oil capacity and specifications
Figures below refer to the 3.6L V6 gasoline engine when replacing the oil filter. Capacity can vary slightly based on maintenance procedures and filter changes.
- Oil capacity with a new filter: 6 quarts (5.7 liters).
- Oil capacity without the filter: about 5 quarts (pre-change estimate).
- Recommended oil type: Dexos1 Gen 2 compliant 5W-30 motor oil, synthetic or synthetic blend.
- Climate note: In extreme temperatures, follow Dexos1 Gen 2 guidelines and GM recommendations in the owner’s manual.
For a typical full-synthetic oil change with a new filter, plan for roughly 6 quarts to bring the crankcase to the correct level, then verify with the dipstick after refilling.
Choosing the right oil and maintaining the level
Use the owner’s manual or GM’s Dexos1 Gen 2 specification. The standard recommendation for the Colorado’s 3.6L V6 is 5W-30, in synthetic or synthetic-blend form. Always replace the oil filter at the same time and check the oil level with the dipstick after the engine has cooled for several minutes to ensure an accurate reading. Regular checks help prevent low-oil conditions and keep the engine in good condition.
Notes on variations and other engines
The 2018 Colorado lineup also offered other powertrains (such as 2.5L I-4 or a 2.8L Duramax diesel). Those engines have different oil capacities. The 3.6L V6 configuration used for the capacity discussed here is the one that typically requires about 6 quarts with a filter.
Summary
For the 2018 Chevy Colorado equipped with the 3.6L V6, the standard oil capacity is about 6 quarts (5.7 liters) with the filter, using Dexos1 Gen 2 5W-30 oil. Verify the exact specification in your owner's manual and adjust for climate or any aftermarket modifications. Regular oil changes with the correct oil and filter help maintain engine longevity.
How many quarts of oil does a Chevy Colorado V6 take?
A Chevy Colorado with a 3.6L V6 engine requires 6 quarts of oil. It's always best to double-check your owner's manual for the exact capacity for your specific model year.
- Capacity: 6 quarts (with filter change)
- Oil Type: SAE 5W-30 full synthetic is recommended for the 3.6L V6 engine
- After refilling: Check the dipstick after running the engine to ensure the level is correct
What oil for 2018 Chevy Colorado V6?
Mobil 1 Full Synthetic Engine Oil 5W-30 5 Quart.
How much oil does a 3.6 L V6 take?
The oil capacity for a 3.6L V6 engine is typically 5 to 6 quarts, but it varies by vehicle model and year. For a 2020 Dodge Charger, it's around 5.9 quarts, while a 2023 Jeep Wrangler requires 5 quarts. Newer Jeeps, such as the 2016-2021 Grand Cherokee and Durango, often require 6 quarts. Always check your specific owner's manual for the most accurate information, as it can differ even within the same engine family.
- 5 quarts: Common in many models like the 2020 Jeep Wrangler and 2025 Ram 1500.
- 5.9 quarts: The capacity for some models, such as the 2020 Dodge Charger.
- 6 quarts: Required for certain vehicles, including the 2013 JK Jeep Wrangler and some 2016-2021 Grand Cherokee and Durango models.
- Check your owner's manual: This is the most reliable source for your specific vehicle's oil capacity.
- After refilling: It's important to check the oil level with the dipstick after refilling to ensure it is correct.
How much oil does a 2018 Chevy Colorado 3.6 L V6 take?
6 quarts
Oil Grade: SEOC3
| Viscosity: | 0W-30 (Below -29°C) 5W-30 (All TEMPS) |
|---|---|
| Capacity: | 6 quarts (with filter). After refill check oil level. |
| Torque: | 18 ft/lbs (Oil Drain Plug) |
| Notes: | (1) This specification has been updated from Dexos 1 Gen 2 to GM Dexos 1 Gen 3. |
