How much oil does a 2.4 L Dodge Caliber take?
The 2.4 L Dodge Caliber generally requires about 5 quarts (4.7 liters) of engine oil when performing a standard oil change with a new filter.
For the Caliber’s 2.4-liter inline-four (the World Gasoline Engine used in many early Caliber models), the typical capacity is around 5 quarts with a new oil filter. If the filter is not replaced, the amount you’ll add is usually closer to 4 to 4.5 quarts. Exact figures can vary slightly by model year and filter type, so always verify with the owner's manual and confirm the level with the dipstick after refilling.
Oil capacity specifics for the Caliber 2.4L
Below are the commonly cited capacities you’re likely to encounter when servicing the Caliber’s 2.4L engine. Use these as a baseline, and always verify with your vehicle’s documentation and dipstick.
- With a new oil filter installed: 5 quarts (approximately 4.7 liters)
- Without replacing the filter (or if the filter is not changed): about 4 to 4.5 quarts (roughly 3.8 to 4.3 liters)
These figures reflect standard maintenance practice for the 2.4L engine in the Caliber. Always rely on the dipstick to confirm the oil reaches the full mark after a fill, and adjust for any variations noted by your manual or dealer recommendations.
Oil change checklist for the Caliber 2.4L
To help you perform a proper oil change and hit the correct fill level, follow these steps.
- Park on level ground and let the engine run briefly to warm the oil, then turn off the engine and engage the parking brake.
- Place a drain pan beneath the oil pan, loosen the drain plug, and allow the old oil to fully drain.
- Remove the old oil filter, prepare the new filter, and install it hand-tight (plus a small additional turn as recommended by the filter manufacturer).
- Reinstall the drain plug and tighten to spec, then open the oil filler cap and pour in the oil. Start with about 4.7–5 quarts (4.5–4.7 liters) depending on whether you replaced the filter.
- Run the engine for a minute, turn it off, and check the oil level with the dipstick. Add small amounts of oil as needed to bring the level to the full mark.
After completing the change, check for leaks, wipe up any spills, and dispose of the used oil properly. Keeping a maintenance log can help you track future service intervals and avoid over- or under-filling.
Summary
The Dodge Caliber with a 2.4 L engine typically takes about 5 quarts (4.7 liters) of oil when performing a standard oil change with a new filter. If the filter isn’t replaced, the fill amount is usually around 4 to 4.5 quarts. Always consult the owner's manual for your specific year and model, and verify the final level with the dipstick after refilling to ensure the oil is at the correct operating level.
How much oil does a 2008 Dodge Caliber 2.4 take?
Engine Oil
Capacity: 5 quarts (with filter). After refill check oil level.
How much oil does a 2.4 L 4 cylinder engine take?
5.6 quarts (with filter).
How much oil does a 2.4 Dodge engine take?
The oil capacity for a Dodge 2.4L engine is 4.3 to 4.5 quarts (or 4.3 liters), though some models like the Dart or certain Journey versions may require slightly more, up to 5.5 quarts. It is crucial to check the specific model year and vehicle manual for the most accurate information, as well as the correct oil viscosity, which is commonly 5W-20 or 0W-20 for these engines.
| Year | Model | Oil Capacity |
|---|---|---|
| 2018 | Dodge Journey | 4.5 quarts (with filter) |
| 2019 | Dodge Journey | 4.3 liters (4.5 quarts with filter) |
| 2020 | Dodge Journey | 4.5 quarts (with filter) |
| 2013-2016 | Dodge Dart | 5.5 quarts (with filter) |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_qPElaZ6eGP2mi-gPofmfoQM_111';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
Important considerations:
- Always check your vehicle's owner's manual for the exact oil capacity and viscosity for your specific year and model.
- If changing the filter, you will need to add more oil than if you are not.
- After refilling, check the oil level with the dipstick and add more if needed to ensure it is within the safe range.
- Use a funnel when adding oil to avoid spills around the engine bay.
How many quarts of oil does a Dodge Caliber take?
The oil capacity for a Dodge Caliber is 4.5 US quarts (4.34.34.3 liters) for the 2.0L engine and 4.7 US quarts (4.44.44.4 liters) for the 2.4L engine, both with a filter change. The recommended oil viscosity is typically 5W-20 for the 2.0L and 0W-40 or 5W-20 for the 2.4L, but always check your owner's manual to be sure.
| Engine Size | Oil Capacity (with filter) | Recommended Viscosity |
|---|---|---|
| 2.0L | 4.5 US quarts (4.34.34.3 L) | 5W-20 |
| 2.4L | 4.7 US quarts (4.44.44.4 L) | 0W-40 or 5W-20 |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_qPElaZ6eGP2mi-gPofmfoQM_124';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
