How much oil does a 4.7 liter engine take?
Most Mopar 4.7L PowerTech V8 engines take about 5 quarts (4.7 liters) of engine oil with a new filter.
The exact amount depends on the precise variant, the oil pan size, and whether the filter is counted as part of the capacity. For precise figures, consult the owner's manual or the manufacturer’s service bulletin for your vehicle.
Understanding the 4.7-Liter engine and oil capacity
The 4.7-liter displacement most often discussed in consumer vehicles refers to the Mopar PowerTech V8 used in Jeep, Dodge, and Chrysler products. Oil capacity figures can vary slightly by model year and market, but the general guideline remains that these engines typically require about five quarts of oil when replacing a filter. Always verify the exact specification for your vehicle to avoid under- or overfilling.
Typical oil capacity for common 4.7L engines
Below are the typical oil capacities for the commonly encountered 4.7L engines. Exact numbers vary by model year, market, and specific engine configuration.
- Baseline: about 5 quarts (4.7 L) with a new filter for the Mopar 4.7L PowerTech V8 used in Jeep, Dodge, and Chrysler products.
- Deeper-pan variants: up to roughly 5.5 quarts (5.2 L) in some configurations with a deeper oil pan or different filter setup.
- Exact specification: always verify with the owner's manual or a service bulletin for your exact model year and market.
When in doubt, start with 5 quarts, run the engine for a few minutes, then check the dipstick and add oil in small increments if the level is below the recommended mark.
How to fill and check oil safely
To ensure you fill the engine correctly and avoid overfilling, follow these steps:
- Park the vehicle on level ground and turn off the engine. Wait 5–10 minutes for the oil to settle.
- Open the hood and locate the dipstick; pull it out, wipe clean, reinsert, then pull again to check the current level.
- Place a drain pan under the oil fill, find the oil filler cap on the valve cover, and remove it.
- Using a funnel, add oil in small increments (about 1/2 quart at a time) and recheck the level with the dipstick after the oil has settled.
- Once the dipstick shows the oil near the full mark, stop and replace the filler cap securely.
- Run the engine for 1–2 minutes, then recheck the dipstick again with the engine off and on level ground.
Overfilling can lead to foaming and engine damage, so proceed cautiously and verify with the dipstick.
Oil type and maintenance tips
Follow the viscosity specified in your owner’s manual. In most climates, 5W-30 is common for older 4.7L Mopar engines, while 5W-20 may be specified for newer models or higher-efficiency standards. Change intervals depend on driving conditions, but a typical schedule is every 5,000–7,500 miles (8,000–12,000 km) for conventional oil, or longer with synthetic oil.
Summary
For the Mopar 4.7L PowerTech V8, the typical oil capacity is around 5 quarts (4.7 liters) with a filter, though exact figures vary by model year and oil pan. Always confirm with the vehicle’s manual, fill slowly, and recheck with a dipstick after the oil settles to ensure you are within the recommended range.
How many quarts of oil are in a Toyota Tundra 4.7 V8?
6.6 quarts
1st generation (2000–2006): 4.8–6.6 quarts. 2nd generation (2007–2021): 4.8–8.5 quart. 3rd generation (2022–present): 7.7 quarts.
What kind of oil does a 2003 Dodge Dakota 4.7 take?
The recommended oil for a 2003 Dodge Dakota 4.7L is SAE 5W-30. The engine requires about 6 quarts of oil when changing the filter, and you can also use 10W-30 if 5W-30 is unavailable and the temperature is above -18∘Cnegative 18 raised to the composed with power cap C−18∘𝐶 (0∘F0 raised to the composed with power cap F0∘𝐹).
- Viscosity: SAE 5W-30 is the preferred viscosity. SAE 10W-30 can be used if ambient temperatures are consistently above -18∘Cnegative 18 raised to the composed with power cap C−18∘𝐶 (0∘F0 raised to the composed with power cap F0∘𝐹).
- Capacity: Approximately 6 quarts of oil are needed when changing the oil filter.
- Type: Full synthetic or synthetic blend oils are recommended for better performance and longer intervals, but conventional oil is also an option.
How many quarts of oil does a 4.7 L engine take?
Capacity: 6 quarts (with filter).
What oil does a 4.7 V8 take?
This will help the oil flow easier and quicker. According to the owner's manual, 5W-30 is the preferred oil for both the 4.7L and the 4.7L High Output engines and is best for environmental operating temperatures below 100ºF.
