What bolt pattern is Gator RSX?
The bolt pattern on John Deere Gator RSX models is typically a 4-lug arrangement on a 110 mm bolt circle (4x110). This is the standard setup for most RSX variants, but exact specifications can vary by year or wheel assembly, so it’s important to verify for your specific machine.
Typical bolt pattern for RSX models
Most RSX versions are built to accommodate four lug bolts arranged around a 110 mm circle. This 4x110 pattern is commonly used by Deere and by many aftermarket wheel suppliers for the RSX line. Always confirm the exact pattern for your particular year and model, especially if you’re shopping for wheels or spacers.
To confirm your exact bolt pattern, you can use the following steps:
- Check the official owner’s manual or Deere parts catalog for your specific RSX model and year to locate wheel/hub specifications.
- Inspect the wheel hub and count the number of lug studs to confirm there are four.
- Measure the bolt circle diameter (BCD) by measuring the center-to-center distance between opposite lug holes.
- Consult with a Deere dealer or a reputable aftermarket wheel supplier to cross-check your vehicle’s VIN/model code against wheel compatibility.
By following these steps, you can confirm the correct bolt pattern and avoid purchasing wheels that won’t fit your RSX.
Compatibility considerations and how to proceed
When replacing wheels, also verify the hub bore size, wheel width, and offset to prevent rubbing or clearance issues. Some aftermarket wheels may require spacers or a different offset to align properly with the Gator RSX’s fenders and suspension.
Notes for variations and verification
While the standard is 4x110 for most RSX models, there can be exceptions based on production year, trim level, or special editions. If you’re uncertain, rely on the dealership, official Deere documentation, or a trusted parts retailer to confirm the exact bolt pattern for your machine.
Summary
In short, the Gator RSX typically uses a 4-lug, 110 mm bolt pattern (4x110). Always verify with the specific year and model for your machine, and follow proper measurement steps or consult a dealer when purchasing wheels or accessories to ensure a proper, safe fit.
What bolt pattern is a RSX?
The 2002-2006 Acura RSX has a 5x114.3 mm (or 5x4.5 inch) bolt pattern. This applies to both the base and Type-S models. Other relevant specifications include an M12x1.5mm lug thread and a 64.1mm center bore.
- Bolt Pattern: 5x114.3 mm (or 5x4.5")
- Lug Thread: M12x1.5mm
- Center Bore: 64.1mm
- Lug Torque: 80 ft-lbs
What lug pattern is a John Deere Gator?
The most common John Deere Gator bolt pattern is 4x137mm. However, some models use a different pattern, such as 5x4.5 inches for some newer XUV and 825i/625I models, so it is crucial to verify the specific bolt pattern for your vehicle before purchasing new wheels.
Common bolt patterns
- 4x137mm: This is the most frequent bolt pattern for a wide range of John Deere Gator models, including many of the XUV and RSX series.
- 5x4.5 inches: Some specific newer Gator models use a 5-lug pattern with a 4.5-inch bolt circle (equivalent to 5x114.3mm).
Why you need to check
- Model variations: Different Gator models, even within the same series, can have different bolt patterns depending on the year and trim.
- Incompatibility: Using wheels with the wrong bolt pattern will not fit and could be dangerous.
How to find the correct bolt pattern for your Gator
- Identify your specific model: Find the model number on your Gator, often located near the steering wheel or on the vehicle's chassis.
- Consult your owner's manual: The owner's manual will provide the exact specifications for your model, including the wheel bolt pattern.
- Measure your current wheels: You can count the number of bolts and measure the distance between the holes.
- Check with a parts supplier: Websites and customer service at parts suppliers can help confirm the correct bolt pattern for your vehicle.
What ATVs use the 4x137 bolt pattern?
ATVs and UTVs with the 4x137 bolt pattern include most modern Can-Am ATV and UTV models (like the Outlander, Commander, and Maverick), Honda Pioneer 1000 and Talon series, and Kawasaki ATVs with a solid rear axle.
Can-Am
- ATVs: Most modern and full-sized models, including the Outlander series.
- UTVs: Most models, such as the Commander, Maverick X3, and Defender series.
Honda
- ATVs: Non-sport ATVs typically use a 4x110 bolt pattern, but the Pioneer 1000 and Talon series use 4x137.
Kawasaki
- ATVs: Models with a Solid Rear Axle (SRA) use a 4x137 bolt pattern, whereas those with Independent Rear Suspension use 4x110.
- UTVs: Mule and Teryx models can use the 4x137 bolt pattern (with a 12mm stud), but some Mule PRO models use a 4x156 pattern.
Other Brands
- John Deere: Some models, like the 550i and 850i, use the 4x137 pattern.
What is the bolt pattern on a Gator RSX?
4 x 137
Bolt Pattern: 4 x 137.
