What is the bolt pattern on a 2009 Toyota 4Runner?
The bolt pattern is 6x139.7 mm (six lugs on a 139.7 mm circle), commonly written as 6x5.5 inches.
In more detail, the 2009 4Runner uses a six-lug configuration on a 139.7 mm bolt circle. This pattern is standard across many Toyota trucks and SUVs from that era, and the hub bore is 106.1 mm. These specs determine wheel compatibility, including aftermarket wheels, hub-centric rings, and spacers if needed.
Before listing the key specifications and practical considerations, this article provides a concise reference to help you verify wheel fitment and avoid common pitfalls when swapping wheels on a 2009 4Runner.
Key specifications you’ll need to confirm when shopping for wheels or performing a wheel swap are listed below.
- Lug count: 6
- Bolt circle diameter: 139.7 mm (6x139.7)
- Center bore: 106.1 mm
- Pattern shorthand: 6x139.7 (often written as 6x5.5 in)
These specifications define wheel compatibility for the 2009 4Runner and are shared with many Toyota trucks and SUVs from that period.
Practical considerations for wheel purchases and installation are summarized here to help you avoid clearance or safety issues.
- Ensure any wheel you buy has a 6x139.7 mm bolt pattern to match the 2009 4Runner.
- Center bore compatibility matters: use exact 106.1 mm or plan for hub-centric rings if the wheel’s bore is larger.
- Brake caliper and rotor clearance: check that the wheel design provides sufficient clearance for the brakes and any protruding calipers.
- Wheel width and offset: select a width and offset that clears suspension components and fenders without rubbing, especially at full steering lock or suspension travel.
- Spacers and adapters: these can affect safety, handling, and legality; consult a professional or the wheel manufacturer before using them.
Concluding note: always verify exact specs with the wheel vendor and your vehicle’s manual, and when in doubt seek guidance from a qualified technician.
Summary
The 2009 Toyota 4Runner uses a 6x139.7 mm bolt pattern (six lugs on a 139.7 mm circle) with a 106.1 mm center bore. This pattern is common among Toyota trucks and SUVs of that era, making many aftermarket wheels compatible as long as hub bore, offset, and brake clearance are properly accounted for. Always confirm the precise requirements for your specific build and consult a professional if you’re unsure.
What Toyota has a 5x150 bolt pattern?
These are standard on vehicles such as Sequoia, Land Cruiser, Tundra, LX, and GX.
What does the 4x108 bolt pattern fit?
The 4x108 bolt pattern is commonly used by vehicle brands such as Mazda, Ford, Saab, Mercury, Volvo, and many more. Wheel sizes that we carry for this bolt pattern are 15, 16, 17, and 18-inch wheels. Our large selection of wheel finishes, designs, and colors can help you truly customize your vehicle.
What is the bolt pattern on a Toyota 4Runner?
All modern Toyota 4Runners use a 6x139.7mm bolt pattern, which is also commonly referred to as 6x5.5 inches. This has been consistent across most model years, from the third generation (1996-2002) up to the current generation, and is a key specification to ensure wheels will fit correctly.
- Metric: $6x139.7$mm
- Imperial: 6x5.56 x 5.56𝑥5.5 inches
- Center Bore: The center bore is a consistent $106.1$mm.
Is 4x100 the same as 4x4 bolt pattern?
Is 4 on 4" Bolt Pattern the Same Size as 4 on 100mm Bolt Pattern. Expert Reply: The 4 on 4" bolt hole pattern for the Loadstar ST175/80D13 Bias Trailer Tire with 13" White Wheel # AM3S030 is a little bit larger than a 4 on 100mm bolt hole pattern so they aren't interchangeable unfortunately.
