What is the drive shaft length of a C10?
The drive shaft length of a Chevrolet C10 pickup truck can vary depending on the specific model year and configuration. However, a typical C10 from the 1960s or 1970s would have a drive shaft length of around 50 to 60 inches.
Understanding the Drive Shaft Length of a C10
The drive shaft is a crucial component in a rear-wheel-drive vehicle like the C10, as it transmits power from the transmission to the rear axle. The length of the drive shaft is determined by several factors, including the wheelbase of the vehicle, the location of the transmission, and the position of the rear axle.
The C10 was produced by Chevrolet from 1960 to 1987, and during this time, the truck underwent several design changes that could affect the drive shaft length. For example, the 1960-1966 C10 models had a shorter wheelbase than the 1967-1972 models, which would result in a shorter drive shaft.
Factors Affecting Drive Shaft Length
- Wheelbase: The distance between the front and rear axles, which determines the overall length of the vehicle. A longer wheelbase generally requires a longer drive shaft.
- Transmission Location: The position of the transmission in relation to the rear axle can affect the drive shaft length. If the transmission is closer to the rear axle, the drive shaft will be shorter.
- Rear Axle Position: The location of the rear axle in relation to the transmission can also impact the drive shaft length. If the rear axle is closer to the transmission, the drive shaft will be shorter.
- Model Year: As mentioned, the C10 underwent design changes over the years, which could result in different drive shaft lengths for different model years.
It's important to note that the exact drive shaft length for a specific C10 model can vary, and it's always best to consult the vehicle's service manual or a professional mechanic for the most accurate information.
What is normal drive shaft length?
around 45 to 45.5 inches
In previous years, driver shafts measured at about 43 inches, but today they come in at around 45 to 45.5 inches in length.
What does C10 stand for?
C10, This nomenclature was used by Chevrolet to distinguish their line of pickup trucks throughout the 1960s to the 1980s. The "C" in C10 stands for "Conventional" in reference to the truck's two-wheel-drive system, while the "10" refers to the half-ton rating of the truck's payload capacity.
How long can a truck drive shaft be?
WHAT'S THE LONGEST STEEL DRIVESHAFT I CAN ORDER? A one-piece steel shaft can't be longer than 72″ from the center of the u-joint at one end to the center of the u-joint at the other end. If you have need for a driveline to be longer than 72″, it can be converted to a 2-piece driveshaft or built using aluminum tubing.
How long is a C10?
The C-10 had two new wheelbases: one of 117.5 inches with a 6.5-inch bed, and 131.5 inches with an 8-foot bed. The truck had an overall length of 191.3 inches (485.9 cm) for the 6.5-foot bed and 212 inches (538.4 cm) for the 8-foot bed. The width in the front was 65.8 inches with a height of 65.8 inches.
What is the average length of a drive shaft?
45.5 to 46.75 inches
Most driver shafts were around 43 inches until the early 1990s. The stock standard now is anywhere from 45.5 to 46.75 inches.
What is the longest driver shaft allowed?
The stock standard now is anywhere from 45.5 to 46.75 inches. There are two reasons for that growth. First, driver head size has increased significantly.
What is the standard length of a driver shaft?
The average driver length for men is now about 45 inches, while women have shorter (but still overall longer) driver shafts that average about 44 inches. Again, the maximum limit for length is 46 inches. Bring out the ruler because driver lengths are getting closer to challenging that regulation limit.
What is the length of a 1972 C10?
1/2-Ton Pickup
| Exterior | |
|---|---|
| Length : | 200.5 in | 5093 mm. |
| Height : | 47.5 in | 1207 mm. |
| Wheelbase : | 115.0 in | 2921 mm. |
What length is my driveshaft?
Start by measuring from the center of the U-joint at the front of the driveshaft to the center of the U-joint at the rear. This will give you the overall length of the driveshaft.
What is the standard length of a shaft?
Standard sizes
The standard lengths of the shafts are 5 m, 6 m and 7 m. Usually 1m to 5m is used.
