What is the torque spec for the 2024 Ford Bronco lug nuts?
The lug nuts on the 2024 Ford Bronco are torqued to 110 ft-lbs (150 Nm) for most factory wheels. This standard value applies to the common wheel configurations, but always verify with the owner’s manual or Ford service data if you’re using aftermarket wheels or adapters.
This article explains the official torque spec, how to apply it correctly, and considerations for variations or aftermarket components, along with best practices to keep wheels secure and safe.
Official spec and how to apply it
The 110 ft-lbs specification is published in Ford’s service documentation for the Bronco and is intended to provide proper clamping force without overstressing fasteners or the wheel. Below are the key details and best practices for applying this spec correctly.
Before applying the torque, read these essential points to ensure you torque the lug nuts correctly:
- Torque value: 110 ft-lbs (150 Nm).
- Torque pattern: use a star/criss-cross sequence to seat the wheel evenly.
- Tooling: use a calibrated torque wrench; avoid relying on impact guns to reach final torque.
- Fasteners condition: ensure lug nuts and studs are clean and dry; do not lubricate unless the manufacturer specifies.
- Initial and ongoing checks: after installation, re-torque to spec after the first 50-100 miles of driving, then periodically as part of maintenance.
Concluding: Following the correct torque value and pattern helps ensure proper wheel seating, safe operation, and longevity of the fasteners.
Wheel variations and aftermarket considerations
Some Bronco owners use different wheel sizes or aftermarket lug nuts, which can affect the recommended torque. Always check the wheel manufacturer guidelines and Ford’s service data for the exact value for your setup. In general, ensure the seat type, thread condition, and lug-nut specification align with the wheel’s requirements.
- Factory-lug torque typically remains 110 ft-lbs, but verify if your wheel configuration differs.
- Hub-centric rings, spacers, or adapters may require a different torque or seating procedure; confirm with the wheel supplier and Ford documentation.
- Maintain the star pattern and re-torque after the first 50-100 miles, even with aftermarket wheels.
Concluding: If you use aftermarket wheels or non-standard components, verify the torque spec with the wheel manufacturer and Ford documentation to avoid under- or over-tightening.
Summary
The official lug-nut torque specification for the 2024 Ford Bronco is 110 ft-lbs (150 Nm) for most factory wheels. Always confirm the correct value for your specific wheel configuration, apply the torque in a star pattern with a calibrated torque wrench, and recheck after 50-100 miles of driving to ensure wheel security and safety.
What to torque Ford Bronco tires to?
Proper torque application is crucial for safely operating your Ford Bronco. The recommended torque specification for most models is 113 Nm (83.3 ft-lb). However, the Bronco Raptor requires a higher torque of 140 Nm (103.5 ft-lb) due to its demanding performance capabilities.
What is the torque on the 2024 Ford Bronco lug nuts?
The 2024 Ford Bronco lug nut torque is 100 ft-lbs (or 135 Nm) for most standard models, but the Bronco Raptor requires a higher 140 Nm (103.5 ft-lbs). For any 2024 Ford Bronco model, it is critical to use a calibrated torque wrench and tighten the lug nuts in a star pattern. It is also recommended to re-check the torque after about 50–100 miles of driving.
| Model | Torque Specification |
|---|---|
| Most 2024 Ford Broncos | 100 ft-lbs (135 Nm) |
| 2024 Ford Bronco Raptor | 140 Nm (103.5 ft-lbs) |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_QtMlacX1ONaui-gPqOWciAo_113';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
You can watch this video to learn how to torque lug nuts correctly on a Ford Bronco: 55sBronco BebopYouTube · Apr 15, 2023
- Use a calibrated torque wrench: This ensures the nuts are tightened to the correct specification.
- Tighten in a star pattern: This is crucial for evenly distributing pressure and preventing warping of the brake rotors.
- Re-check after driving: After the first 50 to 100 miles, it's important to re-torque the lug nuts to ensure they haven't loosened.
- Consult the owner's manual: The most accurate torque specifications can always be found in your vehicle's owner's manual.
What is the Ford Bronco's torque?
The standard 2.3-liter EcoBoost I-4 engine outputs 300 horsepower and 325 pound-feet of torque with premium fuel, a substantial amount of power for a standard powertrain.
What is the torque spec for the 2024 Bronco sport?
The standard engine is a 1.5-liter EcoBoost® four-cylinder that produces 181 horsepower and 190 lb-ft of torque, but you can also opt for a 2.0-liter version that instead makes 250 horsepower alongside 277 lb-ft of torque.
