What size are the nuts on a Ford Edge?
The lug nuts on most Ford Edge models use a 21 mm (13/16 inch) hex size with a 5x114.3 mm bolt pattern. The exact thread pitch can vary by year and wheel, so it’s best to verify for your specific vehicle.
Understanding the Ford Edge lug nut and wheel setup
Across its production span, the Ford Edge has consistently used a 5-lug pattern with a 114.3 mm bolt circle. The typical lug nut hex size you’ll need for standard wheels is 21 mm (13/16 in). The thread pitch and seat type can differ by year and wheel design, commonly ranging around M14 in diameter with pitches such as 1.5 or 2.0. Because wheel options and trims can introduce variations, confirming the exact specification on your vehicle is important.
Common configurations you’re likely to encounter are summarized below. Use this as a quick reference, but always verify on your specific car or wheel set.
- Generations 2007–2010: Bolt pattern 5x114.3 mm; lug nut hex size 21 mm; thread pitch typically M14 with either 1.5 or 2.0 spacing depending on wheel variant. Confirm for your exact vehicle.
- Generations 2011–2014: Bolt pattern 5x114.3 mm; lug nut hex size 21 mm; thread pitch typically M14 with either 1.5 or 2.0 spacing depending on wheel variant. Confirm for your exact vehicle.
- Generations 2015–2023: Bolt pattern 5x114.3 mm; lug nut hex size 21 mm; thread pitch typically M14 with either 1.5 or 2.0 spacing depending on wheel variant. Confirm for your exact vehicle.
These entries reflect the most common setup across model years, but there can be exceptions based on trim, aftermarket wheels, or special editions. Always verify with your owner’s manual or the original wheel hardware from your car.
How to verify the exact nut size for your Edge
To ensure you get the correct lug nuts or a compatible socket, use the following steps to confirm your exact specifications.
- Check the owner’s manual or a factory service manual for the lug nut size and torque specs specific to your year and trim.
- Inspect a lug nut on the wheel you’re removing or replacing; note the hex size (usually 21 mm) and look for any markings that indicate thread size or seat type.
- Measure the hex across flats with a caliper or a ruler if you don’t have a socket handy, then compare to standard sizes (21 mm corresponds to 13/16 inch).
- Identify the wheel bolt pattern on your vehicle: Ford Edge typically uses 5x114.3 mm; this helps confirm compatibility of wheels and nuts.
- If in doubt, provide your VIN to a Ford dealer or reference the exact wheel part number to ensure you’re ordering the correct lug nuts for your vehicle.
Once you have confirmed the exact size and pitch, use the appropriate torque specification and seating method for safe wheel installation. Mismatched thread pitch or improper seating can damage studs or wheels and compromise safety.
Torque and seating considerations
Proper torque ensures both secure wheel mounting and even lug nut load. For Ford Edge vehicles, the general guidance is to torque lug nuts to the manufacturer’s specification, often around 95–110 ft-lbs (approx. 128–150 N·m), depending on the year and wheel type. Always use the correct seating type (usually conical/60-degree seat for Ford wheels) and re-torque after the first 50–100 miles of driving to account for settling. If you’re unsure, consult the owner’s manual or a professional technician.
Summary
In short, the Ford Edge typically uses 21 mm (13/16 in) lug nuts with a 5x114.3 mm bolt pattern. The exact thread pitch and seat type can vary by year and wheel, so verifying on your specific vehicle is essential. Use the owner’s manual, VIN-based resources, or a professional to confirm before purchasing replacements or performing a wheel service.
What size lug nuts are on a 2007 Ford Edge?
The lug nut size for a 2007 Ford Edge is 1/2-20 thread with a 13/16-inch (or 21mm) hex size. These are standard acorn-style lug nuts that thread clockwise (right-hand thread) and feature a conical 60-degree seat.
Lug nut specifications
- Thread size: 1/2−201 / 2 minus 201/2−20
- Hex size: 13/1613 / 1613/16 inch or $21$mm
- Seat style: Conical (60-degree)
- Thread direction: Right-hand thread
Important considerations
- Stock vs. Aftermarket: While 1/2−201 / 2 minus 201/2−20 is the standard for the 2007 Ford Edge, always verify the correct specifications for your vehicle, especially if you have aftermarket wheels, as they may require a different size or seat style.
- Professional installation: For proper and safe installation, it is recommended to consult your owner's manual or a professional installer.
What size socket for Ford wheel nuts?
The most common socket size for Ford lug nuts is 13/16" or 21mm, especially for models like the F-150 and Bronco. However, sizes can vary by model year and specific vehicle, with some models like the Bronco Sport using a 19mm (or 3/4") socket. It is best to confirm the exact size for your vehicle, as some older or different models might use a different size.
- 13/16" or 21mm: This is the most common size for many modern Ford vehicles, including the F-150 and Bronco. Some sources suggest 13/16" may be a slightly tighter fit than 21mm, which can help prevent rounding the lug nuts.
- 19mm (or 3/4"): This size is used on certain models, such as the Bronco Sport.
- Verification: It's important to check your vehicle's manual or confirm the size before buying tools, especially since some models use a different size or have swollen lug nuts that may require a special socket.
- Swollen lug nuts: If you have a Ford with swollen lug nuts, a standard socket may not fit. In these cases, a special "flip" socket, which has a slightly larger size, can be used to remove them.
What size are Ford lug nuts?
Most modern Ford vehicles use M14x1.5 lug nuts, while some older models and certain trucks use M12x1.25 or M14x2.0. The most common size for a F-150 from around 2015 onwards is M14x1.5, and for F-250s it is M14x1.5. For older F-150s (2004-2014), the size is M14x2.0, and many other models like the Escape, Focus, and Fusion use M12x1.25. Always check your owner's manual for the specific size for your vehicle.
| Lug Nut Size | Common Vehicles |
|---|---|
| M14x1.5 | Most 2015+ F-150s, F-250s, Explorers, and Mavericks |
| M14x2.0 | 2004-2014 F-150s, 2003-2014 Expeditions, 2003-2014 Navigators |
| M12x1.25 | 2001-2022 Escape, 2012-2018 Focus, 2006-2020 Fusion, 2011-2022 Fiesta, 2019-2026 Ranger (including Raptor), 2021-2026 Bronco (non-Raptor) |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_7tElaYP-Jqe6i-gPk_eO4Qk_264';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
What size are the lug nuts on a Ford Edge?
*If the Lug Hole Diameter is Smaller Than 1.19"(30mm), This Set Will NOT Fit
| Make | Model | Orig. Stud |
|---|---|---|
| Ford | Edge | M14x1.5 |
| Ford | Explorer | M14x1.5 |
| Ford | GT | M14x1.5 |
| Ford | Mustang | M14x1.5 |
