What size are the wheel nuts on a 2014 Ford Focus?
The wheel nuts for a 2014 Ford Focus are typically M12 x 1.5 with a 60-degree conical (tapered) seat, used on a 5-lug pattern (5x108 mm). The center bore is about 63.4 mm, and the standard tightening torque is around 95 ft-lbs (approximately 128 Nm).
These specifications cover the common factory configuration for 2014 Focus models in many markets. However, wheel sizes and aftermarket options can affect hardware, so verify against your specific vehicle by checking the owner’s manual, the door placard, or the wheel manufacturer’s specifications, especially if you’re using aftermarket wheels or spacers.
Key wheel-nut specifications
Typical measurements you’ll encounter when inspecting or replacing lug nuts on a 2014 Focus are listed below.
- Bolt pattern: 5x108 mm
- Lug nut thread size: M12 x 1.5
- Seat type: 60-degree conical (tapered) seat
- Center bore: 63.4 mm
- Recommended torque: ≈95 ft-lbs (≈128 Nm)
These specs reflect the standard factory configuration for most 2014 Focus models. If you’re using aftermarket wheels or a non-standard setup, confirm the nut size and torque with the wheel manufacturer or a qualified technician.
Notes on verification and maintenance
Because regional and trim variations can exist, always verify the exact spec for your vehicle. The following guidance helps ensure you install wheels safely and correctly.
How to verify on your vehicle
Consult the owner’s manual or the driver’s door placard for the exact lug pattern, nut size, and torque. If in doubt, measure the current lug nuts and consult a dealer or a professional with your VIN to confirm the correct specifications.
Maintenance and safe torque practices
Use a properly calibrated torque wrench and tighten to the specified value. Re-torque after mounting new wheels or after 50–100 miles of driving, and avoid using impact wrenches beyond recommended settings to prevent stud damage.
Summary
For a 2014 Ford Focus, expect lug nuts to be M12 x 1.5 with a 60-degree conical seat, on a 5x108 bolt pattern with a 63.4 mm center bore. Tighten to about 95 ft-lbs (≈128 Nm). Always verify with your specific vehicle configuration, especially if you have aftermarket wheels or alterations.
What size socket for Ford Focus wheel nuts?
The correct wheel nut socket size for a Ford Focus is 19mm. The lug nuts are also specified as having an M12x1.5 thread size. For best results, use a deep, 12-point, and quality-made socket to avoid damaging the nuts, especially if they are rounded.
- Socket size: 19mm
- Thread size: M12x1.5
- Recommendation: Use a quality 19mm socket that fully fits the nut to prevent rounding. Avoid adjustable or shallow sockets.
What size socket is a 2014 Ford Fusion lug nut?
The lug nut socket size for a 2014 Ford Fusion is a 19mm socket. The lug nuts use a metric M12x1.5 thread size.
- Socket size: 19mm
- Thread size: M12x1.5
What size socket are Ford lug nuts?
The most common socket size for Ford lug nuts is 13/16" or 21mm, especially for models like the F-150 and Bronco. However, sizes can vary by model year and specific vehicle, with some models like the Bronco Sport using a 19mm (or 3/4") socket. It is best to confirm the exact size for your vehicle, as some older or different models might use a different size.
- 13/16" or 21mm: This is the most common size for many modern Ford vehicles, including the F-150 and Bronco. Some sources suggest 13/16" may be a slightly tighter fit than 21mm, which can help prevent rounding the lug nuts.
- 19mm (or 3/4"): This size is used on certain models, such as the Bronco Sport.
- Verification: It's important to check your vehicle's manual or confirm the size before buying tools, especially since some models use a different size or have swollen lug nuts that may require a special socket.
- Swollen lug nuts: If you have a Ford with swollen lug nuts, a standard socket may not fit. In these cases, a special "flip" socket, which has a slightly larger size, can be used to remove them.
What size are the lug nuts on a 2014 Ford Focus?
Dorman – Wheel Lug Nut: M12-1.50 Thread, Conical 60, OEM Style, 0.553" Length, Chrome, 4 Pack (Part No. 711-832)
