What size wrench for Honda oil drain plug?
The typical wrench size for a Honda oil drain plug is 14mm, which fits most modern Honda engines. Some older or specialty models may require a 17mm. Always confirm by checking your owner’s manual or inspecting the plug head before attempting removal.
Common sizes you’ll encounter on Honda engines
The sizes listed below reflect what you’re most likely to encounter on Honda cars and light trucks. Model and year can influence the exact requirement.
- 14 mm hex head: This is by far the most common size for many recent Honda engines, including various Civic, Accord, CR-V, and Fit models, among others.
- 17 mm hex head: Some older or less common Honda engines use a 17 mm drain plug. If the 14 mm socket doesn’t fit, carefully test a 17 mm socket to avoid rounding the head.
In practice, begin with the 14 mm socket. If it fails to engage or slips, stop and recheck the plug head for wear or an alternate design, then proceed cautiously with the appropriate size.
Verifying the correct size for your Honda
To confirm the exact size for your vehicle, follow these steps:
- Consult the owner’s manual or a service manual specific to your model and year for the drain plug size and torque specification.
- Inspect the drain plug head and count the flats or measure across the opposite sides to compare with standard sizes (14 mm vs 17 mm).
- If uncertain, refer to a dealer or authorized mechanic to avoid damaging the plug or threads.
Using the correct size helps prevent stripping the drain plug and ensures a proper seal when refilling oil. Always replace the crush washer as required and follow the manufacturer’s torque specification when reinstalling.
Summary
Most Honda oil drain plugs use a 14mm wrench, with 17mm encountered on some older or exceptional models. Verify the size through the manual or by inspecting the plug head, and proceed carefully to avoid damage. If in doubt, seek professional assistance.
What size socket for 2016 Honda Civic oil drain plug?
So let's get to it engage the emergency parking brake raise the front of the vehicle with a floor jack support the vehicle on jack stands locate the oil drain plug use a 17 mm socket to loosen. It.
What size is the oil plug on a Honda Civic?
The Honda Civic oil plug size is typically M14 x 1.50 mm, and it uses a 17 mm socket to remove and install. This is consistent across most recent models, though it is always best to confirm with your specific vehicle's owner's manual.
- Thread Size: M14 x 1.50 mm
- Socket/Wrench Size: 17 mm
- Gasket: It is also recommended to replace the crush washer every time you change the oil.
What size socket for Honda oil plug?
A 17mm socket is the most common size for a Honda oil drain plug, though some models like certain V6 Accords may use a 19mm socket. To be certain, check your specific vehicle's manual or use a 17mm socket as the most likely size to start.
This video shows how to change the oil on a 2016-2020 Honda Civic: 20sXJ JesseYouTube · Jul 5, 2023
- 17mm: This is the standard size for many Honda models, including most Civics and some Accords.
- 19mm: This size is used on some other Honda models, particularly the 3.5L V6 engine in some Honda Accords.
- Verification: It's always best to confirm the size for your specific vehicle by checking the owner's manual or by trying the 17mm socket first, as it is the most frequently used size.
What size is a Honda Accord oil plug?
The oil drain plug for a Honda Accord is typically M14 x 1.50mm with a 17mm hex head, though some specific models or aftermarket plugs may have a different head size like 16mm. The most accurate way to confirm the correct size for your specific year and model is to check the part number or consult your owner's manual.
Drain plug specifications
- Thread size: M14 x 1.50mm
- Head size: Typically a 17mm hex head, but may vary depending on the model year and whether it's an original or aftermarket part.
- Confirm your size: Always verify the correct size for your vehicle before purchasing a replacement plug.
