Where is the power window fuse located on a 2002 Ford Explorer?

The power window fuse on a 2002 Ford Explorer is typically in the driver’s-side interior fuse box, usually a 20A fuse labeled Power Windows. Some models may also use a fuse in the engine compartment; always check the fuse diagram on the panel cover or the owner's manual for your exact trim.

Where to find the fuse locations

Use the following locations to check the power window fuse in a 2002 Explorer. The two most common spots are the interior fuse box and, in some configurations, the engine compartment box.

• Interior fuse box: Located behind the panel on the driver’s side of the dash (the kick-panel area). The inside of the fuse panel cover shows the circuit diagram and the amperage for the Power Windows fuse.


• Engine compartment fuse/relay box: Some configurations route the power window circuit through a fuse in the under-hood box. Refer to the cover diagram for the exact designation if your vehicle uses this layout.

In most Explorers from this era, the interior fuse box is the primary source for the power window fuse, with the engine compartment box used only on certain trims or configurations.

Fuse amperage and labeling

Understanding the label helps ensure you replace the correct fuse and avoid electrical issues. The following guidelines reflect typical labeling you’ll encounter.

• Power Window fuse: Usually 20-amp, labeled "P/W," "Power Windows," or "Power Window" on the fuse panel.


• Power Window relay: Some models may use a relay as part of the circuit; if present, it is usually located in the same fuse/relay box or integrated into the power window circuit in the dash. The exact location can vary by trim.

Always replace a blown fuse with one of the same amperage rating and recheck the fuse box diagram to confirm the correct designation for your specific vehicle.

What to do if the fuse is blown or the window still doesn’t work

Follow these steps to diagnose and address common issues without risking damage to the electrical system.

1. Turn off the ignition and locate the suspected Power Windows fuse in the interior fuse box. Use the fuse puller or a pair of insulated pliers to remove it and inspect for a broken element or a darkened appearance.


2. Replace the blown fuse with a new fuse of the same amperage (typically 20A for Power Windows). If the fuse blows again, there may be a short or motor/wiring fault in the window circuit.


3. Check the driver’s door window switch and the wiring harness at the door for signs of damage or loose connections.


4. Inspect the door jamb wiring, especially where the harness bends as the door opens and closes, for fraying or pinch damage that could cause a short.


5. If a relay is used in your configuration, test or replace the Power Window relay as described in the owner's manual or service manual.

If the fuse continues to blow after these checks, it’s advisable to consult a qualified technician to diagnose deeper electrical faults or a failing window motor.

Summary

For a 2002 Ford Explorer, the power window fuse is most commonly found in the driver’s-side interior fuse box and is typically a 20A fuse labeled Power Windows. Some builds may include an additional fuse in the engine compartment, so always verify with the fuse panel diagram on the cover or the vehicle’s manual. If the fuse blows, replace it with the correct amperage and inspect the switch, wiring, and window motor for faults, seeking professional help if needed.

Where is the fuse for the power windows located?

The power window fuse is typically located in a fuse box under the dashboard on the driver's side or under the hood, according to Glass Doctor and JustAnswer. You can find the exact location and the correct fuse number for your vehicle in the owner's manual or on the diagram on the fuse box cover itself.
 
This video shows how to locate the fuse box and the power window fuse in a car: 58sCarsNToysYouTube · Nov 25, 2020

• Locate the fuse box: Check the fuse box under the dashboard on the driver's side, near the steering wheel, or the main fuse box located under the hood. 
• Find the diagram: Consult your owner's manual or the diagram on the fuse box cover to identify the correct fuse for the power windows (it may be labeled "P/W" or "Power Window"). 
• Check the fuse: Once you have located the fuse, inspect it to see if the metal strip inside is broken or melted, which indicates it is blown. 
• Replace if necessary: If the fuse is blown, replace it with a new one of the same amperage rating. 

Where is the fuse for power windows on a 2002 Ford Explorer?

Towards some pliers that are made especially for fuses. So you can reach these ones a bit more easily. Anyway this is the first location for the second one we need to pop the hood of this car.

How do I reset the window on my Ford Explorer?

To reset a Ford Explorer window, open the affected window all the way, holding the switch for a few seconds after it's fully down, then close it all the way, holding the switch for a few seconds after it's fully up. Some methods also suggest performing a full up and down cycle twice to fully reinitialize the system. 
Standard reset procedure

1. Ensure the affected window is fully closed. 
2. Press and hold the window switch down until the window is completely open. 
3. Continue holding the switch down for 2-3 seconds after it is fully open. 
4. Lift and hold the switch up until the window is completely closed. 
5. Continue holding the switch up for 2-3 seconds after it is fully closed. 

This video demonstrates how to reset the power windows on a Ford Explorer: 56sTuned 2.7YouTube · Nov 17, 2023
Alternative reset method

• Some sources recommend repeating the standard procedure one or two more times for a more thorough reset. 
• Another method involves holding the switch for a longer period (5-10 seconds) in both the up and down positions after the window reaches its limit. 

Important notes

• For a successful reset, complete the steps within 30 seconds of starting. 
• Be cautious during the reset process as the window will close with high force. Ensure no objects or body parts are in the path of the window. 
• If the problem persists, there may be a more significant issue, such as a faulty window regulator, motor, or wiring, which may require professional inspection. 

What is the fuse for the power windows on a 2003 Ford Explorer?

That's the fuse block under the hood adjacent to the battery. Power to all window motors begins at fuse F1. 6 -- 60 amp.