How many quarts of oil does a 2007 Dodge Nitro 3.7 L take?
The 2007 Dodge Nitro with the 3.7-liter V6 typically requires 5 quarts of engine oil when changing the oil with a new filter; without the filter, about 4.5 quarts.
This article explains the official capacity, practical variations you may encounter, and best practices for a proper oil change on the Nitro’s 3.7 L V6, including tips on oil grade and dipstick checks.
Official oil capacity and guidance
Below are the common service-capacity figures used during routine oil changes. They assume a new oil filter is installed and the engine is drained of old oil.
- With filter: 5 quarts (approx. 4.7 L)
- Without filter: about 4.5 quarts (approx. 4.3 L)
- Note: After filling, always start the engine, run for a few minutes, then recheck the level with the dipstick and top off as needed to reach the full mark.
These figures reflect standard service practice and may vary slightly with different oil filter brands or aftermarket parts. Always verify the level on the dipstick after an initial fill and adjust as necessary.
Oil grade considerations
For the 3.7 L V6 used in the Nitro, the typical recommendation is 5W-20 as the baseline, with 5W-30 considered in hotter climates or under certain conditions. Always consult the owner's manual or a trusted service source for the exact grade recommended for your climate and mileage, as using the correct viscosity helps with wear protection and fuel efficiency.
Practical steps for an oil change
To perform an oil change on the Nitro’s 3.7 L engine, follow these steps in order.
- Prepare supplies: the correct grade of oil (as specified in the manual), a new oil filter, an oil drain pan, a funnel, a socket for the drain plug, and rags or shop towels.
- Warm the engine briefly to help drain oil more completely, then place the vehicle on level ground and chock the wheels.
- Position the drain pan under the oil pan, remove the drain plug, and let the old oil fully drain out.
- Remove the old oil filter, clean the mounting surface, and install a new filter according to the manufacturer’s instructions (do not over-tighten).
- Replace the drain plug with a new washer if required, then pour in the recommended amount of new oil (start with 5 quarts for a filter change).
- Run the engine for a few minutes, turn it off, wait a few minutes for the oil to settle, and then check the dipstick. Add oil in small increments until the level reaches the full mark.
- Dispose of the used oil and filter properly at a recycling facility or service station.
Following these steps helps ensure a clean oil change with accurate oil level, reducing the risk of overfill or low oil pressure.
Summary
For the 2007 Dodge Nitro with a 3.7 L V6, plan on about 5 quarts of engine oil when performing a standard oil change with a new filter; approximately 4.5 quarts if the filter is not replaced. Use the recommended oil grade for your climate, verify the level with the dipstick after filling, and follow proper disposal practices for old oil. With these guidelines, you’ll maintain proper lubrication and engine health for this vehicle.
How much oil does a 3.7 Dodge Nitro take?
5.0 qt.
Engine Speed 6000 rpm (electronically limited) Fuel Requirement Unleaded regular, 87 octane Oil Capacity 3.7 L (5.0 qt.) Coolant Capacity 13.25 L (14.0 qt.)
PDF
How many quarts of oil does a 3.7 L engine take?
A 3.7-liter engine typically requires 6 quarts of oil with a filter change, although specific capacities can vary by vehicle make and model. For example, a Ford 3.7L engine often takes 6 quarts, while a Jeep 3.7L might take 5 quarts, so it's essential to consult your vehicle's owner's manual for the exact amount.
- Ford 3.7L engines: Require about 6 quarts (5.7 L) of oil when changing the filter.
- Jeep 3.7L engines: May require about 5 quarts of oil with a filter change.
- Always check your owner's manual: This is the most accurate source for your specific vehicle's oil capacity.
What kind of oil does a 2008 Dodge Nitro 3.7 take?
The correct oil for a 2008 Dodge Nitro with a 3.7L engine is SAE 5W-20. The vehicle requires approximately 5 quarts of oil when changing the filter. Both synthetic and conventional oils in the 5W-20 weight are compatible, but the owner's manual should always be consulted for the most accurate information.
- Oil Weight: SAE 5W-20
- Capacity: 5 quarts (with filter)
- Type: Can use synthetic or conventional oil, as long as it meets the 5W-20 specification. Some products also meet the API SP or ILSAC GF-6A specifications, as outlined by Advance Auto Parts and AutoZone.
- Recommendation: Always check your owner's manual for the most specific recommendation for your vehicle.
What kind of motor oil does a 2007 Dodge Nitro take?
The 2007 Dodge Nitro takes either SAE 5W-20 oil for its 3.7L V6 engine or SAE 10W-30 oil for its 4.0L V6 engine. Always consult your owner's manual to confirm the correct oil type for your specific engine and to determine the correct oil capacity.
| Engine Size | Recommended Oil |
|---|---|
| 3.7L V6 | SAE 5W-20 |
| 4.0L V6 | SAE 10W-30 |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_mNIlabz6G8uii-gP-b3_oAc_148';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
